System Description
The powertrain control module (PCM) identifies an engine misfire by detecting the variations in crankshaft speed. The crankshaft speed variations can also occur when a vehicle is operated over a rough surface. The anti-lock brake system (ABS) can detect when the vehicle is on a rough surface based on the wheel acceleration/deceleration data supplied by each wheel speed sensor. The (electronic brake control module (EBCM) over the Class 2 Serial Data line sends this information to the PCM. The PCM then uses this information in order to determine if the crankshaft variations are being caused by an actual engine misfire or from being driven on a rough surface.
Whenever the ABS is found to be malfunctioning, the PCM will still continue to detect for misfire. However, if a misfire DTC is set, this additional DTC P1380 will also set, indicating that rough surface data was not usable during the misfire detection due to the ABS malfunction.
Conditions for Running the DTC
| • | A DTC P0300-P0304 has been set. |
| • | The vehicle speed is more than 8 km/h (5 mph). |
Conditions for Setting the DTC
An ABS DTC is set.
Action Taken When the DTC Sets
| • | The PCM records the operating conditions at the time the diagnostic fails. The Failure Records buffers stores this information. |
| • | A history DTC is stored. |
Conditions for Clearing the DTC
| • | A history DTC clears after 40 consecutive warm up cycles without a fault. |
| • | The scan tool can clear the DTC. |
Diagnostic Aids
The setting of this DTC indicates that a misfire was detected and that the PCM could not determine if the detected misfire was true or due to operating the vehicle on a rough surface. A misfire can be a true misfire with or without setting this DTC. Check the EBCM for poor connections at the Class 2 Serial Data terminals. Be sure no true misfire exists after repairing the cause of this DTC.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
The Powertrain OBD System Check prompts the technician to complete some basic checks and store the Freeze Frame and Failure Records data on the scan tool if applicable. This creates an electronic copy of the data taken when the malfunction occurred. The information is then stored on the scan tool for later reference.
-
ABS DTCs are found by selecting Chassis on the scan tool.
-
Refer to A Diagnostic System Check - ABS in Antilock Brake System (ABS) for ABS DTCs and repairs.
-
Be careful to clear only DTCs and not the captured information stored on the scan tool. The scan tool will issue a warning if this is about to happen.
-
A DTC P1380 being reset indicates that the PCM is not receiving the correct information from the EBCM due to an ABS DTC.
-
When DTC P1380 is set, an ABS DTC should also be set.
-
Repair any condition that remains and is causing a misfire by following the table for any DTC that has set.
-
The replacement PCM must be programmed and the Crankshaft Position System Variation Learn Procedure must be preformed.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | |||
Were any ABS DTCs set? | -- | |||
Repair the condition causing the ABS DTC. Refer to Diagnostic Starting Point in Antilock Brake System (ABS). Is the action complete? | -- | -- | ||
Important: Be careful to clear only DTCs and not the captured information stored on the scan tool. The scan tool will issue a warning if this is about to happen. Did a misfire DTC set? | -- | |||
Was a DTC P1380 also set? | -- | |||
Did a ABS DTC also set? | -- | |||
Repair the condition causing the misfire. Is the action complete? | -- | -- | ||
Important: The replacement PCM must be programmed. Is the action complete? | -- | -- | ||
9 |
Does the scan tool indicate that this diagnostic has Ran and Passed? | -- | ||
10 | Check if any additional DTCs are set. Are any DTCs displayed that has not been diagnosed? | -- | Go to applicable DTC table | System OK |
