The mass air flow (MAF) sensor is an air flow meter that measures the amount of air entering the engine. The powertrain control module (PCM) uses the MAF sensor frequency signal in order to provide the correct fuel delivery for a wide range of engine speeds and loads. A small quantity of air entering the engine indicates a deceleration or idle. A large quantity of air entering the engine indicates an acceleration or high load condition. The MAF sensor has an ignition 1 voltage circuit, a ground circuit and a signal circuit. The PCM applies a voltage to the sensor on the signal circuit. The sensor uses the voltage in order to produce a frequency based on inlet air flow through the sensor bore. The frequency varies within a range of around 2,000 Hertz at idle to about 10,000 Hertz at maximum engine load. DTC P0103 sets if the PCM detects a frequency signal higher than the possible range of a properly operating MAF sensor.
• | The engine is running for more than 2 seconds. |
• | The engine speed is more than 400 RPM. |
• | The ignition 1 signal is more than 8 volts. |
• | The MAF sensor frequency is stable for more than 1 second. |
The PCM detects that the MAF sensor frequency signal is more than 12,000 Hz.
• | Any water that enters the air intake system that reaches the MAF sensor could cause this DTC to set. The water rapidly cools the hot sensing elements in the sensor causing a false indication of excessive air flow. Inspect the following areas for evidence of water intrusion: |
- | The air induction system. |
- | The secondary air injection system (AIR) if equipped. |
• | A poor connection in the ignition 1 voltage circuit of the MAF sensor can cause a DTC P0103 to set. |
If you suspect the condition may be related to aftermarket accessories, refer to Checking Aftermarket Accessories in Wiring Systems.
If the condition is intermittent, refer to Intermittent Conditions.
The numbers below refer to the step numbers on the diagnostic table.
This step tests for Electromagnetic Interference (EMI) on the signal circuit of the MAF sensor. A frequency reading with the MAF sensor disconnected indicates an EMI related fault or a poor connection. Disconnecting the MAF sensor may set additional related DTCs.
This step eliminates any conditions which can cause a DTC to set with a normally operating MAF sensor.
Step | Action | Values | Yes | No | ||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||||||||||
1 | Did you perform the Diagnostic System Check-Engine Controls ? | -- | Go to Step 2 | Go to A Diagnostic System Check-Engine Controls | ||||||||
2 |
Does the DTC fail this ignition? | -- | Go to Step 3 | Go to Diagnostic Aids | ||||||||
Does the scan tool display the specified value? | 0 Hz | Go to Step 5 | Go to Step 4 | |||||||||
Inspect the harness of the MAF sensor for incorrect routing that is too close to the following components:
Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 6 | |||||||||
5 | Test for an intermittent and for a poor connection at the MAF sensor. Refer to Testing for Intermittent and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 7 | ||||||||
6 | Test for an intermittent and for a poor connection at the PCM. Refer to Testing for Intermittent and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 8 | ||||||||
7 | Replace the MAF sensor. Refer to Mass Air Flow (MAF) Sensor Replacement. Did you complete the replacement? | -- | Go to Step 9 | -- | ||||||||
8 | Replace the PCM. Refer to Powertrain Control Module (PCM) Replacement. Did you complete the replacement? | -- | Go to Step 9 | -- | ||||||||
9 |
Does the DTC run and pass? | -- | Go to Step 10 | Go to Step 2 | ||||||||
10 | With a scan tool, observe the stored information, Capture Info. Does the scan tool display any DTCs that you have not diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List | System OK |