GM Service Manual Online
For 1990-2009 cars only

Tools Required

J 41396 Park Lock Cable Pliers

Removal Procedure


    Object Number: 324874  Size: SH

    Caution: This vehicle is equipped with a Supplemental Inflatable Restraint (SIR) System. Failure to follow the correct procedure could cause the following conditions:

       • Air bag deployment
       • Personal injury
       • Unnecessary SIR system repairs
    In order to avoid the above conditions, observe the following guidelines:
       • Refer to SIR Component Views in order to determine if you are performing service on or near the SIR components or the SIR wiring.
       • If you are performing service on or near the SIR components or the SIR wiring, disable the SIR system. Refer to Disabling the SIR System.

  1. Disable the SIR system. Refer to Disabling the SIR System in SIR.
  2. Remove the knee bolster. Refer to Knee Bolster Replacement in Instrument Panel, Gauges and Console.
  3. Install the steering column upper and lower trim covers. Refer to Steering Column Trim Covers Replacement - On Vehicle .
  4. Remove the automatic transmission shift lock actuator. Refer to Automatic Transmission Shift Lock Actuator Replacement in Shift Lock Control.
  5. Disconnect the park lock cable (1).
  6. The steering column lock cylinder set should be in the off-lock position.
  7. Insert a small screwdriver into the slot on the lock module assembly and push against the locking tab to remove.

  8. Object Number: 662195  Size: SH
  9. Disconnect the automatic transmission shift lock control electrical connector from the park position switch.
  10. Remove the park position switch from the linear shift assembly.

  11. Object Number: 324916  Size: SH
  12. Remove the linear shift assembly mounting screws.
  13. Remove the linear shift assembly from the steering column.
  14. To disassemble the linear shift assembly, proceed to the next step.

  15. Object Number: 324909  Size: SH
  16. Remove the gear shift lever assembly mounting bolt.
  17. Remove the ball and actuator assembly (2) from the gear shift lever assembly.
  18. Remove the shift lever clevis (1) from the support bracket for the gear shift lever assembly.

  19. Object Number: 324897  Size: SH
  20. Remove the shift gate mounting screws.
  21. Remove the park lock cable assembly from the support bracket for the gear shift lever assembly.

  22. Object Number: 324900  Size: SH
  23. Remove the cable shift cam assembly (1) mounting bolt.
  24. Remove the cable shift cam assembly (1) from the support bracket for the gear shift lever assembly.
  25. Remove the cam bushing (2) from the cable shift cam assembly (1).

  26. Object Number: 324902  Size: SH
  27. Remove the support bracket for the gear shift lever assembly mounting screws.
  28. Remove the gear shift lever assembly support bracket from the steering column support assembly.

Installation Procedure


    Object Number: 324902  Size: SH

    Important: Lubricate all of the moving parts of the linear shift assembly with synthetic grease.

  1. Install the gear shift lever assembly support bracket onto the steering column support assembly.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the gear shift lever assembly mounting screws.
  4. Tighten
    Tighten the gear shift lever assembly mounting screws to 10 N·m (89 lb in).


    Object Number: 324900  Size: SH
  5. Insert the cam bushing (2) into the cable shift cam assembly (1).
  6. Install the cable shift cam assembly (1) into the support bracket for the gear shift lever assembly.
  7. Install the cable shift cam assembly (1) mounting bolt.
  8. Tighten
    Tighten the cable shift cam assembly mounting bolt to 18 N·m (14 lb ft).


    Object Number: 324897  Size: SH
  9. Install the park lock cable assembly onto the support bracket for the gear shift lever assembly.
  10. Install the shift gate and park lock cable assembly mounting screws.
  11. Tighten
    Tighten the shift gate and park lock cable assembly mounting screws to 6.5 N·m (58 lb in).


    Object Number: 324909  Size: SH
  12. Install the shift lever clevis (1) into the support bracket for the gear shift lever assembly.
  13. Install the ball actuator assembly (2) onto the gear shift lever assembly.
  14. Install the gear shift lever assembly mounting bolt.
  15. Tighten
    Tighten the gear shift lever assembly mounting bolt to 18 N·m (14 lb ft).

  16. To install the linear shift assembly as an assembly, proceed to the next step.

  17. Object Number: 324916  Size: SH
  18. Install the linear shift assembly mounting screws.
  19. Tighten
    Tighten the linear shift assembly mounting screws to 10 N·m (89 lb in).


    Object Number: 662195  Size: SH
  20. Install the park position switch to the linear shift assembly.
  21. connect the automatic transmission shift lock control electrical connector to the park position switch.

  22. Object Number: 324874  Size: SH
  23. Connect the park lock cable assembly (1) to the lock module in the following way:
  24. • Place the steering column lock cylinder set into the off position.
    • Place the shift lever clevis into the park position.
    • Press the locking tab on the end of the park lock cable assembly (1) into the slot in the lock module.

    Object Number: 324884  Size: SH
  25. Adjust the park lock cable assembly.
  26. 16.1. Use the shift lever clevis to put the column in the park position.
    16.2. Put the ignition switch in the off-lock position. Remove the key.
    16.3. Unlock the adjuster ring (1) on the park lock cable assembly with J 41396
    16.4. Pull on the cable until the park lock latch contacts the shift lever clevis. Release the cable.
    16.5. Lock the adjuster ring (1) securely in place on the park lock cable assembly with J 41396 .
  27. Inspect the park lock cable assembly.
  28. 17.1. Put the lock cylinder in the off-lock position. The shift lever clevis should not be able to shift out of the park position.
    17.2. Turn the key to the run position and put the shift lever clevis in the neutral position.
    17.3. With the shift lever clevis in the neutral position the lock cylinder should not be able to go into the off-lock position.
    17.4. Put the shift lever clevis into the park position.
    17.5. Put the lock cylinder in the off-lock position and then remove the key.
  29. Install the automatic transmission shift lock control actuator. Refer to Automatic Transmission Shift Lock Actuator Replacement in Shift Lock Control.
  30. Install the steering column upper and lower trim covers. Refer to Steering Column Trim Covers Replacement - On Vehicle .
  31. Install the knee bolster. Refer to Knee Bolster Replacement in Instrument Panel, Gauges and Console.
  32. Enable the SIR system. Refer to Enabling the SIR System in SIR.