Radio/Audio System Description and Operation w/o CTF
The Radio/Audio System consists of 1 of 2 levels of audio entertainment:
Both levels of audio entertainment contain a speaker system that is
appropriate for each radio/audio level and a choice of radios that contain
various options.
Radio/Audio System Content
Base Level Audio
System
|
UM7 Radio with AM/FM Stereo
| UM6 Radio with AM/FM Stereo and Auto-Reverse Cassette
|
Fixed Mast Antenna
| Fixed Mast Antenna
|
Uplevel Audio System
|
UL0/UP0 Radio with AM/FM Stereo and Auto-Reverse Cassette. UP0 includes
a single CD Remote Playback Device
| UN0 Radio with AM/FM Stereo and CD Player
| U1F (Available on Oldsmobile Only) Radio with AM/FM Stereo and Auto-Reverse
Cassette With CD Remote Playback Device
|
Fixed Mast Antenna
| Fixed Mast Antenna
| Fixed Mast Antenna
|
Optional Multiple CD Remote
Playback Device
| Optional Multiple CD Remote Playback Device
| Optional
Multiple CD Remote Playback Device
|
Optional BOSE audio amplifier
| Optional BOSE audio amplifier
| BOSE audio amplifier
|
Optional Rear Seat Audio Controller
| Optional Rear Seat Audio Controller
| --
|
Optional Steering Wheel Controls
| Optional Steering
Wheel Controls
| Steering Wheel Controls
|
Playing the Radio - Base Level
VOLUME-BAL
• | The ignition switch must be in the ACCESSORY or RUN position to
operate the radio. |
• | The radio power switch is integral with the volume control. |
• | Use the radio power switch/volume control knob in order to turn
the system ON and OFF and to control the volume. |
• | Turn the radio power switch clockwise in order to turn the system
ON or to increase the volume. |
• | Turn the radio power switch counterclockwise in order to turn
the system OFF or to decrease the volume. |
RECALL
• | The RECALL function can only be performed with the radio ON. |
• | Press the volume control knob to toggle the display between the
time of day or the radio frequency. |
• | Press the volume control knob to briefly display the time of day
while the radio is turned OFF. |
Finding a Station (Base Level)
AM-FM
Press the tune knob in order to change the radio band between AM and
FM. The display will indicate the current band and the last radio frequency
that was selected on that band.
TUNE
• | Rotate the TUNE knob clockwise in order to increase the AM or
FM frequency. |
• | Rotate the TUNE knob counterclockwise in order to decrease the
AM or FM frequency. |
SEEK
• | Press the right arrow button in order to tune into the next station
higher in frequency. |
• | Press the left arrow button in order to tune into the next station
lower in frequency. |
SCAN
- Press both SEEK buttons in order to activate the SCAN mode.
- SCAN will appear on the display and the radio will stop at every
station for a few seconds.
- Press the right arrow button in order to tune into the next higher
station
- Press the left arrow button in order to tune into the next lower
station.
- Press VOLUME or both SEEK buttons to stop scanning.
PUSH BUTTONS
Up to 14 stations can be preset into the radio's memory using the numbered
push buttons (1,3,5, and 7). In order to preset 4 AM and 4 FM stations,
perform the following steps:
- Tune to the desired radio station.
- Press the SET push button. SET will appear on the display.
- Press and hold a numbered push button until the SET display goes
off. The radio will tune to the preset station the next time the same push
button is pressed.
In order to preset 3 additional AM and 3 additional FM stations perform
the following steps:
- Tune to the desired radio station.
- Press the SET push button. SET will appear on the display.
- Press and hold two adjacent push buttons (1 and 3) until
the SET display goes off. The radio will tune to the preset station the next
time both push buttons are pressed.
- Repeat the first 2 steps for each remaining pair of push buttons
(3 and 5, or 5 and 7).
Setting the Tone - Base Level
BASS
• | Slide the BASS lever up in order to increase the bass response. |
• | Adjust the BASS lever down in order to decrease the bass response. |
TREB
• | Slide the TREB level up in order to increase the treble response. |
• | Slide the TREB lever down in order to reduce the noise if the
station is weak or noisy. |
Adjusting the Speakers - Base Level
BAL
• | Turn the BAL control knob behind the VOLUME knob to select more
or less sound, distributed between the left or the right speakers. |
• | The middle position will deliver an equal balance of sound between
the left and right speakers. |
FADE
• | Turn the FADE control knob behind the TUNE knob to select more
or less sound, distributed between the front and rear speakers. |
• | The middle position will deliver an equal balance of sound between
the front and rear speakers. |
Playing a Cassette Tape - Base Level
- In order to play a tape, the ignition switch must be in the ACCESSORY
or RUN position and the receiver must be turned ON.
Tapes are
end-loaded into the cassette player.
- Insert the tape squarely through the door, exposed tape side of
the cassette facing to the right.
- When the tape is fully inserted, the AM/FM portion of the radio
will turn off and the tape will begin playing.
- The tape player works best with tapes that are 30-45 minutes
long on each side.
Longer running tapes may not work well in
these players because they are usually too thin.
- Once the tape is playing, the volume, balance and fade knobs operate
the same as with the radio.
An arrow indicates which side of
the tape is being played.
FWD
- Press the SEEK right arrow key in order to fast forward the tape.
- Press the SEEK left arrow key in order to stop the fast forward
operation.
REV
- Press the SEEK left arrow key in order to rewind the tape.
- Press the SEEK right arrow key in order to stop rewinding the
tape.
RECALL
Press the volume control knob to change from one side of the tape to
the other.
EJECT
Press the EJECT push button in order to remove the tape or in order
to stop the tape and switch to the radio.
CLN
- If CLN appears on the display, the cassette player needs to be
cleaned in order to prevent damage to the tape player.
- After cleaning the tape player, press and hold the EJECT button
for 5 seconds in order to reset the CLN indicator.
- The radio displays "- - -" in order
to show that the indicator has been reset.
Playing the Radio - Uplevel
PWR-VOL
• | Push the PWR-VOL knob in order to turn the radio ON and
OFF. |
• | Rotate the volume control clockwise in order to increase the volume. |
• | Rotate the volume control counterclockwise in order to decrease
the volume. |
RECALL
• | The RECALL function can only be performed with the radio ON. |
• | Press the RECALL push button to toggle the display between the
time of day or the radio frequency. |
• | Press the RECALL push button to briefly display the time of day
while the radio is turned OFF. |
Speed Compensated Volume (SCV)
• | In order to use the SCV, adjust the volume to the listening level
you want and move the control ring behind the PWR-VOL knob to adjust the
SCV. |
• | The volume level automatically adjusts to compensate for road
and wind noise as you drive. |
• | As you drive, the volume level will change in order to compensate
for the noise present at any particular speed. |
• | Each detente on the SCV allows for more compensation at a faster
rate. |
Finding a Station - Uplevel
AM-FM
• | Press the AM/FM push-button to switch between AM, FM1, and FM2. |
• | The display indicates the current band. |
TUNE
- Press lightly on the TUNE control in order to release the tune
control from the tune control's recessed position.
- Rotate the TUNE knob to the right in order to increase the frequency.
- Rotate the TUNE knob to the left in order to decrease the frequency.
- Push the TUNE control back in order to store the frequency setting
while not tuning.
SEEK
• | Press the right arrow key in order to tune into the next higher
frequency. |
• | Press the left arrow key in order to tune into the next lower
frequency. |
| Audio is muted during the SEEK operation. |
SCAN
- Press and hold SEEK for 2 seconds. SCAN will appear on
the display.
- Use SCAN in order to listen to each radio station for a few seconds.
- Press SEEK again in order to stop scanning.
PUSH BUTTONS
Up to 18 stations (6 AM, 6 FM1, and 6 FM2) can be preset into the radio's
memory using the 6 numbered push buttons. In order to preset a station in
memory, perform the following steps:
- Press AM-FM in order to select the band.
- Tune to the desired station, using the TUNE knob or SEEK.
- Press AUTO TONE in order to select the setting that you prefer.
- Press and hold 1 of the 6 push buttons until audio returns, approximately
2 seconds.
- Whenever you press that push button, the preset station will return.
The AUTO TONE that you selected will also be automatically selected
for that push button.
PSCAN
Any stations already stored in preset memory can be sampled by the PSCAN
mode.
- In order to use PSCAN, press the PSCAN push button.
PSCAN will scan each of the presets and stop for a few seconds.
- Press PSCAN or another push-button in order to stop scanning to
listen to a specific station.
PSCAN appears in the display whenever
the tuner is in the PSCAN mode.
If 1 of the stations stored on
a push-button is weak, the radio display shows the channel number (P1-P6)
for several seconds before advancing to the next preset station.
Setting the Tone - Uplevel
AUTO TONE
The automatic tone control (ATC) feature tailors the equalization to
the type of broadcast being received.
- Press AUTO TONE in order to step through the 6 preset equalization
settings of CLASSIC, NEWS, ROCK, POP, JAZZ, or C/W (Country Western).
Note the graph and words in the display for each press of the push button.
- One or more presses of the AUTO TONE push-button brings up manual
(MAN) and return the control of tone back to the TREB and BASS controls.
- Any time that a BASS or TREBLE control rotates, the tone automatically
sets to MAN.
BASS
- Depress the BASS control in order to remove the control from the
recessed position.
- Rotate the BASS control to the right in order to increase the
bass response.
- Rotate the BASS control to the left in order to decrease the bass
response.
- Operation of this control will switch the radio's AUTO TONE feature
to MAN.
- Push the control knob back in to store when not in use.
TREBLE
- Depress the TREB control in order to remove the control from the
recessed position.
- Pull the TREB control out to a fully extended position in order
to make TREB adjustments.
- Rotate the TREB control to the right in order to increase the
treble response.
- Rotate the TREB control to the left in order to decrease the treble
response.
- Operation of this control will switch the radio's AUTO TONE feature
to MAN.
- Push the control knob back in to store when not in use.
Adjusting the Speakers - Uplevel
BALANCE
- Depress the BAL control in order to remove the control from the
recessed position.
- Rotate the balance to the right in order to adjust the sound to
the right speakers.
- Rotate the balance to the left in order to adjust the sound to
the left speakers.
- Push the control knob back in to store when not in use.
FADE
- Depress the FADE control in order to remove the control from the
recessed position.
- Rotate the FADE control knob to the right in order to adjust the
sound to the front speakers.
- Rotate the FADE control knob to the left in order to adjust the
sound to the rear speakers.
- Push the control knob back in order to store when not in use.
Playing a Cassette Tape - Uplevel
- Tapes may be played with the ignition ON or OFF.
If the ignition is ON but the radio is OFF, the tape will begin playing.
A tape symbol, accompanied by tape direction arrows, is shown in the
center of the graphic display whenever a tape is playing.
- Tapes are end-loaded into these players. Insert the tape squarely
through the door, exposed tape side of the cassette facing the right.
- When the tape is fully inserted, the AM/FM portion of the radio
will turn OFF and the tape will begin playing.
- The tape player works best with tapes that are 30 to 45 minutes
long on each side. Longer tapes may not work well in the cassette player
because the tapes are so thin.
- To load a cassette with the ignition in the OFF position, press
EJECT or RECALL.
- Insert the cassette.
- If the ignition is in the ON position and the radio is in the
OFF position, the tape will begin to play.
- The player automatically senses the tape cartridge for metal or
Cr02 tape media and presets the pre-emphasis.
For metal tapes,
"DD" will be displayed.
- Any time a tape is playing, use the volume, balance, fade, treble,
and bass just as with the radio.
An arrow indicates which side
of the tape is being played.
- When you insert a tape, the top of the cassette plays first.
PREV
• | Press the PREV or the SEEK left arrow push button in order to
search for the previous selection. |
| The tape direction arrow blinks
during SEEK operation. |
• | A minimum 3 second blank gap is required for proper operation. |
• | Audio is muted during SEEK. |
PROG
Press the PROG push button in order to switch from one side of the tape
to the other.
NEXT
• | Press the NEXT or the SEEK right arrow push button in order to
search for the next selection. |
• | A minimum of a 3 second gap is required for the player to stop
at the beginning of a selection. |
• | The tape direction arrow will blink during the SEEK operation. |
REV
• | Press REV in order to rewind the tape. The tape rapidly reverses
to the beginning of the cassette or until you press the REV push-button a
second time. |
| The radio plays the last selected station
during the REV operation. |
• | The tape direction arrow blinks during REV operation. |
DOLBY®
Dolby Noise Reduction is manufactured under a license from Dolby Laboratories
Licensing Corporation.
Dolby® and the "DD" symbol are trademarks of Dolby Laboratories
Licensing Corporation.
- Press the Dolby push-button in order to reduce cassette tape noise.
- The "DD" Dolby® symbol will appear in the display.
FWD
- Press FWD in order to fast-forward the tape. The tape rapidly
advances to the end of the tape or until you press the FWD push-button again.
- The radio will play the last selected station during the FWD operation.
- The tape direction arrow blinks during FWD operation.
AM-FM
Press the AM-FM button in order to switch from tape to radio.
TAPE AUX
- Press TAPE AUX in order to return to the tape player.
- The lighted arrow appears and shows the direction of play when
a tape is in the active mode.
EJECT
- In order to remove the tape, press EJECT.
- EJECT may be activated with either the ignition or the radio
OFF.
- Cassettes may be loaded with the radio OFF by pressing EJECT before
loading the cassette tape.
CLN
- If CLN appears on the display, the cassette player needs to be
cleaned in order to prevent damage to the tape player.
- After cleaning the tape player, press and hold EJECT for 5 seconds
in order to reset the CLN indicator.
- The radio displays "- - -" in order
to show that the indicator reset.
Playing a Compact Disc - Uplevel
PWR
- Press the PWR knob in order to turn the system on.
- The system can be turned on by inserting a compact disc into the
player with the ignition in the ON position.
- Insert a disc partway into the slot, label side up.
- The player pulls the disc in.
- When inserted, the disc will begin playing track 1.
- Wait a few seconds until the disc plays.
- The letters "CD" and a CD symbol appears on the display.
- If the disc comes back out and ERR appears on the display, inspect
for the following conditions:
• | The disc is upside down. |
• | The disc is dirty, scratched, or wet. |
• | There is too much moisture in the air. |
• | Wait an hour
and try again. |
• | The vehicle is operating on a very rough road. |
• | The disc player is very hot. |
- Press RECALL in order to eliminate the ERR message.
RECALL
- Press the RECALL button in order to see what track is playing.
- Press the RECALL button again within 5 seconds in order
to see the elapsed time of the current track.
- The track number appears when a new track begins to play.
- Press RECALL again in order to return to the time display.
PREV
• | Press PREV or the SEEK left arrow in order to search for the previous
selection. |
• | If you hold the PREV button or press it more than once, the disc
advances further. |
RDM
- The random playback (RDM) feature allows the tracks on the compact
disc to be played in random order rather than in sequential order.
- During random playback, a RANDOM indicator appears in the display.
- Press RDM again in order to return to normal play.
NEXT
- Press NEXT or the SEEK right arrow in order to search for the
next selection.
- If you hold the NEXT button or press it more than once, the disc
will advance further.
- The next track number will appears on the display.
REV
- Press and hold the REV button in order to quickly reverse within
a track.
- When the CD reverses, elapsed time displays in order to find the
correct passage.
FWD
- Press and hold the FWD button in order to quickly advance within
a track.
- When the CD advances, elapsed time displays in order to find the
correct passage.
AM-FM
- While in the CD mode, press the AM-FM button in order to
stop playing the CD and play the radio.
- The CD symbol will still be displayed but the letters CD are replaced
with AM, FM1, or FM2.
- If the radio is turned OFF, the disc will remain in the player
and resume playing at the point where it stopped, when the radio is turned
ON.
CD AUX
- Press the CD AUX button in order to return from listening to the
radio and play the CD.
- When a disc plays, the letters "CD" and the CD symbol
will appear on the display.
- If the radio is turned OFF, the disc will remain in the player
and resume playing at the point where it stopped, when the radio is turned
ON.
EJECT
• | Press EJECT in order to eject the disc from the CD player. |
• | A disc that has been ejected but not removed from the player will
be pulled back in within 30 seconds. |
| This protects the
disc and the player from damage. |
• | The disc does not play. |
• | In order to remove the disc, press the EJECT button and remove
the disc from the player. |
Remote Playback Device - Uplevel
In order to operate the Compact Disc player, perform the following steps:
- Insert a disk part way into the slot, label side up.
- If the radio is in the OFF position and the ignition is in the
ON position when you insert the CD, the radio turns on and begins playing
the CD.
- In order to load a CD with the ignition in the OFF position, press
the EJECT button on the remote player and insert the disc.
- In order to remove the disc, press the EJECT button and remove
the disc.
- All of the compact disc functions are controlled by the radio
buttons except EJECT.
- When a disc is in the player, a CD symbol appears next to the
CD symbol in the bottom left corner on the display.
The track
number will also be displayed .
- If the disc comes back out and ERR appears on the display, inspect
for the following conditions:
• | A dirty, scratched, or wet disc |
• | Too much moisture in the air |
• | If there is too much
moisture in the air, wait about 1 hour and try again. |
• | The vehicle is operating on a very rough road. |
TAPE AUX
- With a disc loaded in the player and the radio playing, press
the TAPE AUX button once in order to play the compact disc.
- Press AM-FM in order to return to the radio.
- If you load both a cassette and a CD, press TAPE AUX in order
to switch between the tape and the compact disc.
SEEK
- Press the left arrow while playing a CD in order to go back to
the beginning of the current track.
- The CD goes back to the current track if more than 8 seconds
have played.
- Press the left arrow again in order to go to the previous tracks.
- Press the right arrow in order to go to the next higher track
on the disc.
PREV
- Press PREV in order to go back to the beginning of a current track.
- The CD goes back to the current track after 8 seconds have
played.
- Press PREV again in order to go the previous track on the disc.
PROG
The PROG button functions only when the vehicle is equipped with a 12-disc
changer.
NEXT
Press the NEXT button in order to advance to the next track on the disc.
REV
- Press and hold the REV button in order to quickly reverse within
a track.
- When the CD reverses, elapsed time displays in order to find the
correct passage.
FWD
- Press and hold the FWD button in order to advance within a track.
- When the CD advances, elapsed time displays in order to find the
correct passage.
RANDOM
- Press PSCAN in order to enter the RANDOM play mode.
RANDOM will appear on the display.
- While in this mode, the tracks on the disc will be played in random
order.
- If you press the SEEK, PREV, or NEXT buttons while in the random
mode, the PREV or NEXT track scans randomly.
- Press PSCAN again in order to turn off RANDOM and return to normal
operation.
EJECT
• | Press EJECT in order to eject the disc from the CD player. |
• | A disc that has been ejected but not removed from the player will
be pulled back in within 30 seconds. |
• | This protects the disc and the player from damage. |
• | The disc does not play. |
• | In order to remove the disc, press the EJECT button and remove
the disc from the player. |
RECALL
- Press RECALL in order to see what track is playing.
- Press RECALL again within 5 seconds in order to view elapsed
time.
- Press RECALL a third time and the time of day will be displayed.
Theftlock™ - Uplevel
Important: Read all steps before starting the procedure.
If more than 15 seconds elapse between any of the steps, the
radio automatically reverts to time and you must start the procedure over
from step 4.
If SEC appears on the display in step 4, the system has already been
activated.
To change the code, the old code must be removed first.
In order to activate the Theftlock™ system, perform the following
steps:
- Write down any number from 000 to 1999.
- Turn the ignition to the ACCESSORY or the RUN position.
- Turn the radio OFF.
- Press the 1 and 4 push-buttons together. Hold them down until
"- - -" shows on the display.
- Press MN and 000 will appear on the display.
- Press and hold MN again until the last two digits agree with your
code.
- Press and hold HR to make the first one or two digits agree with
your code.
- Press the AM/FM push button after you have confirmed that the
code matches the code you wrote down. If REP appears on the display, repeat
steps 5 through 8.
- SEC will appear on the display, the radio is now operable and
secured.
- With the ignition OFF, the Theftlock™ indicator flashes.
Activating the Theftlock™ Feature
Important: Read all steps before starting the procedure.
If more than 15 seconds elapse between any of the steps, the
radio automatically reverts to time and you must start the procedure over
from step 4.
If SEC appears on the display in step 4, the system has already been
activated.
To change the code, the old code must be removed first.
In order to activate the Theftlock™ system, perform the following
steps:
- Write down any number from 000 to 1999.
- Turn the ignition to the ACCESSORY or the RUN position.
- Turn the radio OFF.
- Press the 1 and 4 push-buttons together. Hold them down until
"- - -" shows on the display.
- Press MN and 000 will appear on the display.
- Press and hold MN again until the last two digits agree with your
code.
- Press and hold HR to make the first one or two digits agree with
your code.
- Press the AM/FM push button after you have confirmed that the
code matches the code you wrote down. If REP appears on the display, repeat
steps 5 through 8.
- SEC will appear on the display, the radio is now operable and
secured.
- With the ignition OFF, the Theftlock™ indicator flashes.
Unlocking a Radio That Displays LOC When Code is Known
Important: Read all steps before starting the procedure.
If more than 15 seconds elapse between any of the steps, the
radio automatically reverts to time and you must start the procedure over
from step 4.
In order to unlock the Theftlock™ system after a power loss, perform
the following steps:
- Write down the users code.
- Turn the ignition to the RUN position.
- Press MN and 000 will appear on the display.
- Press and hold MN until the last 2 digits agree with the code.
- Press and hold HR until the first one or two digits agree with
the code.
- Press the AM/FM push button after you have confirmed that the
code matches the one you wrote down. If REP appears on the display, repeat
steps 3 through 6.
- SEC will appear on the display, the radio is now operable and
secured.
If the wrong code is entered more than eight times, INOP will appear
on the display.
Wait one hour before attempting to unlock the radio again.
This time only 3 attempts will be allowed before INOP appears on the
display.
If this happens you must wait 1 hour before attempting to unlock the
radio again.
Unlocking a Radio That Displays LOC When Code is Unknown
Important: Starting in 1995, a factory back-up code can be used to erase the original
code if it is unknown.
Have account number ready to enter when asked. Account number is your
5 digit dealer code followed by one of these numbers:
Read all steps before starting the procedure.
If more than 15 seconds elapse between any of the steps, the
radio automatically reverts to time and you must start the procedure over
from step 1.
In order to unlock the Theftlock™ system when code is unknown,
perform the following steps:
- Press and hold push buttons 2 and 3 until a three digit code appears
on the display.
- Write the three digit code on a piece of paper.
- Press the AM/FM push button, a three digit code will appear on
the display again.
- Write the three digit code on a piece of paper.
- Call Delco Electronics at 1-800-537-5140.
- Follow the computer prompts to obtain the back-up code to
be used in place of unknown code.
- Press MN and 000 will appear on the display.
- Press and hold MN until the last two digits agree with the back-up
code.
- Press and hold HR until the first one or two digits agree with
the back-up code.
- Press the AM/FM push button after you have confirmed that the
code matches the one you wrote down. If REP appears on the display, repeat
steps 7 through 10.
- The display will show "- - -" to
indicate unknown code has been removed.
If the back-up code does not unlock the radio, try reversing the
first and last three digits of the display code.
If this is unsuccessful, call Delco Electronics to obtain a new factory
back-up code.
Disabling the Theftlock™ Feature
Important: If more than 15 seconds elapse between any of the steps, the
radio automatically reverts to time and you must start the procedure over
from step 3.
In order to disable the Theftlock™ feature, enter the user code
as follows:
- Turn the ignition to ACCESSORY or RUN.
- Turn the radio OFF.
- Press the 1 and 4 buttons together. Hold then down until SEC appears
on the display.
- Press MN and "000" will appear on the display.
- Press and hold MN until the last two digits agree with the user
code.
- Press and hold HR until the first one or two digits agree with
the user code.
- Press the AM/FM push button after you have confirmed that the
code matches the one you wrote down. If REP appears on the display, repeat
steps 4 through 7.
- The display will show "- - -", indicating
that the radio is no longer secured.
- If the code is entered incorrectly, SEC appears on the display.
- The radio will remain secured until the correct code is entered.
Rear Seat Audio (RSA)
The rear seat audio controller feature allows the rear seat passengers
to listen to a different music source than the front seat passengers including
the cassette tape and the remote compact disc (CD) players.
For example, the rear seat passengers may listen to the cassette
or CD through headphones while the driver listens to the radio through
the front speakers. The rear seat passengers have control of the
volume for each headphone. Be aware that the primary radio controls
always override the rear seat audio controls.
Seek (SEEK)
The sound will mute while seeking. The SEEK button is inactive when
the front radio is also using the SEEK feature. Use the following procedure
in order to seek:
- Press the up arrow in order to tune to the next higher station
(with enough strength) and stay there.
- Press the down arrow to tune to the next lower station (with enough
strength) and stay there.
Use the following procedure in order to seek selections on a cassette
tape:
- Press the up arrow in order to hear the next selection on the
tape.
- Press the down arrow in order to go back to the previous selection.
Use the following procedure in order to seek selections on a compact
disc:
- Press the up arrow in order to immediately listen to the next
track instead of waiting until the current track is finished.
- Hold the up arrow button or press it more than once in order to
advance to further tracks.
- Press the down arrow in order to go to the start of the current
track if more than 8 seconds have played.
Power (PWR)
Press this button in order to turn the rear seat audio system ON or
OFF. The rear speakers mute when the power is turned ON. You may operate the
rear seat audio functions even when the primary radio power is off.
Band Switching - AM/FM
Press the AM/FM button in order to switch between AM, FM1 and FM2. The
selection appears on the display. If the front passengers are already listening
to AM-FM, the rear seat audio controller will not switch between the
bands and cannot change the frequency.
Source Switching - TAPE CD
Use the following procedure in order to switch between listening sources:
- Press the TAPE CD button in order to activate the source switching
feature. There must be a cassette tape and/or compact disc in the player.
- Press the TAPE CD button in order to switch between the cassette
tape and the compact disc functions.
Preset Program (PSET PROG)
The front passenger must be listening to something different for the
PSET PROG to operate. Press the PSET PROG in order to use the following
functions:
• | To seek through your preset radio stations that are set on your
primary radio push-buttons. |
• | To go to the other side of the cassette tape while the cassette
is playing. |
• | To change discs when a compact disc is playing. This button will
no operate if used with a single remote compact disc player. |
Use the following procedure in order to operate the volume control:
- Press lightly on the VOL knob in order to extend the knob.
- Turn the knob clockwise in order to increase the volume.
- Turn the knob counterclockwise in order to decrease the volume.
- Push the knob in when you are not using the volume control.