GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 2001 🢒 Sonoma Pickup - 2WD 🢒 Body and Accessories 🢒 Body Control System 🢒 DTC B2585

Circuit Description

The body control module (BCM) monitors the voltage on the Interior park lamps fused supply voltage circuit in order to determine the actual state of the park lamp relay. The BCM also uses the park lamp relay control circuit in order to energize the park lamp relay.

Conditions for Running the DTC
    • The key is in the RUN position.
    • The park brake is released.
    • The headlamp and panel dimmer switch is in the AUTO mode.
    • The ambient light sensor is in the DARK state.
    • The system voltage must be between 9 and 16 volts.

Conditions for Setting the DTC
    • The key is in the RUN position.
    • The park brake is released.
    • The headlamp and panel dimmer switch is in the AUTO mode.
    • The ambient light sensor is in the DARK state.
    • There is a short to ground in the Interior park lamps fused supply voltage circuit or an open in the park lamp relay control circuit.
    • If the Interior park lamp fused supply voltage circuit is open, regardless of the headlamp and panel dimmer switch position, the DTC will set.
    • If the park lamp relay control circuit is open, with the headlamp and panel dimmer switch in the AUTO mode, the DTC will set.
    • The system voltage must be between 9 and 16 volts.
    • The above conditions must be met for 0.5 seconds.

Action Taken When the DTC Sets

The park lamps will be inoperative in the AUTO mode.

Conditions for Clearing the MIL/DTC
    • A current DTC will clear immediately when the condition for setting the fault is corrected with the key ON.
    • A history DTC will clear after 100 consecutive ignition cycles without a fault present.
    • Use a scan tool in order to clear the history and current DTCs.

Diagnostic Aids

Important: Use the appropriate probe from the J 35616 for any probing of electrical components in this table, in order to prevent damage to them.

Perform a visual inspection for loose or poor connections at all related components. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Command both the ON and OFF states. Repeat the commands as necessary.

    2.

  2. This step determines if the condition is located on the coil side or the switch side of the circuit.

    3.

  3. This step determines if the body control module (BCM) is providing ground for the park lamp relay.

    4.

  4. This step determines if a ground is constantly being applied to the park lamp relay.

    5.

  5. After you replace the BCM, you must calibrate the new module for proper operation.

Step

Action

Yes

No

Schematic Reference: Exterior Lights Schematics

1

Did you perform the Lighting System Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - Lighting Systems

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the park lamps relay ON and OFF.

Does the scan tool display ON and OFF in the Park Lamp Relay Outputs Data List with each command?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

3

With a scan tool, command the park lamp relay ON and OFF.

Do you hear a click when you command the park lamp relay ON and OFF?

Go to Step 9

Go to Step 4

4
  1. Turn OFF the ignition.
  2. Disconnect the park lamp relay.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the PARK LPS voltage circuit of the park lamp relay coil with a test lamp that is connected to a good ground. Refer to Electrical Center Identification Views in Wiring Systems.

Does the test lamp illuminate?

Go to Step 5

Go to Step 19

5

  1. Connect a test lamp between the control circuit of the park lamp relay and the PARK LPS voltage circuit of the park lamp relay coil. Refer to Electrical Center Identification Views in Wiring Systems.
  2. With a scan tool, command the park lamp relay ON and OFF .

Does the test lamp turn ON and OFF with each command?

Go to Step 16

Go to Step 6

6

Does the test lamp remain illuminated with each command?

Go to Step 8

Go to Step 7

7

Test the control circuit of the park lamp relay for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 24

Go to Step 17

8

Test the control circuit of the park lamp relay for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 24

Go to Step 23

9

Turn ON the ignition, with the engine OFF.

Do the park lamps operate continuously?

Go to Step 10

Go to Step 11

10
  1. Turn OFF the ignition.
  2. Disconnect the park lamp relay.
  3. Turn ON the ignition, with the engine OFF.

Do the park lamps operate continuously?

Go to Step 18

Go to Step 22

11
  1. Turn OFF the ignition.
  2. Disconnect the park lamp relay.
  3. Probe the PARK LPS voltage circuit of the park lamp relay switch with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

Go to Step 12

Go to Step 20

12

Connect a 3 amp fused jumper wire between the PARK LPS voltage circuit of the park lamp relay switch and the supply voltage circuit of the park lamps.

Do the park lamps operate and does the scan tool display ON in the Park Lamp Relay Outputs Data List?

Go to Step 16

Go to Step 13

13

Test the park lamp switch output circuit and the fuse output- interior park lamp circuit for an open, high resistance, or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 24

Go to Step 14

14

Test the ground circuit of the park lamps for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 24

Go to Step 15

15

Inspect for poor connections at the headlamp panel dimmer switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 24

Go to Step 21

16

Inspect for poor connections at the park lamp relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 24

Go to Step 22

17

Inspect for poor connections at the harness connector of the body control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 24

Go to Step 23

18

Test the supply voltage circuit of the park lamps for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 24

--

19

Repair the PARK LPS voltage circuit of the park lamp relay coil. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 24

--

20

Repair the PARK LPS voltage circuit of the park lamp relay switch. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 24

--

21

Replace the headlamp and panel dimmer switch. Refer to Headlamp Switch Replacement .

Did you complete the replacement?

Go to Step 24

--

22

Replace the park lamp relay.

Did you complete the replacement?

Go to Step 24

--

23

  1. Replace the BCM. Refer to Body Control Module Replacement in Body Control System.
  2. Program the BCM with the proper calibrations. Refer to Body Control Module (BCM) Programming/RPO Configuration in Body Control System.
  3. Perform the learn procedure.

Did you complete the replacement?

Go to Step 24

--

24

Operate the system in order to verify the repair.

Did you correct the condition?

Go to Step 2

System OK