GM Service Manual Online
For 1990-2009 cars only

Endgate Handle Replacement Pickup

Removal Procedure

  1. Use a flat-bladed tool in order to remove the pickup box endgate latch handle bezel.

  2. Object Number: 300356  Size: SH
  3. Perform the following steps in order to remove the endgate latch rods from the endgate latch handle:
  4. 2.1. Separate the retaining clip from the lower latch rod by prying the clip apart at the head of the latch rod.
    2.2. Slide the lower latch rod from the retaining clip and the handle.
    2.3. Lift the endgate latch handle in order to gain access to the upper latch rod retaining clip.
    2.4. Separate the upper latch rod retaining clip from the upper latch rod.
    2.5. Slide the upper latch rod from the retaining clip.

    Object Number: 738  Size: SH
  5. Remove the bolts that retain the pickup box endgate latch handle to the endgate.
  6. Remove the pickup box endgate latch handle from the endgate.

Installation Procedure

  1. Install the pickup box endgate latch handle to the endgate.

  2. Object Number: 738  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the bolts that retain the pickup box endgate latch handle to the endgate.
  4. Tighten
    Tighten the bolts to 25 N·m (18 lb ft).

  5. Install the upper latch rod to the handle.
  6. Install the upper latch rod to the retaining clip.
  7. Install the lower latch rod to the handle.
  8. Install the lower latch rod to the retaining clip.

  9. Object Number: 300356  Size: SH
  10. Perform the following steps in order to install the pickup box endgate latch:
  11. 7.1. Position the bezel.
    7.2. Press the bezel into place.

Endgate Handle Replacement Utility

Removal Procedure


    Object Number: 392927  Size: SH
  1. Remove the handle grip screws.
  2. Remove the liftgate trim panel. Refer to Liftgate Trim Panel Replacement .
  3. Release the liftgate handle rod retainer.

  4. Object Number: 392928  Size: SH
  5. Remove the bolts that retain the liftgate outside handle to the liftgate.

  6. Object Number: 300370  Size: SH
  7. Remove the liftgate outside handle from the liftgate.

Installation Procedure


    Object Number: 300370  Size: SH
  1. Install the liftgate outside handle to the liftgate.

  2. Object Number: 392928  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the bolts that retain the liftgate outside handle to the liftgate.
  4. Tighten
    Tighten the bolts to 4 N·m (35 lb in).


    Object Number: 392927  Size: SH
  5. Install the liftgate handle rod to the liftgate handle.
  6. Engage the retainer.
  7. Install the liftgate trim panel. Refer to Liftgate Trim Panel Replacement .