DTC P0713 Transmission Fluid Temperature (TFT) Sensor Circuit High Input 2.2L
Circuit Description
The Automatic Transmission Fluid Temperature (TFT) Sensor is part of the Automatic Transmission Fluid Pressure Manual Valve Position Switch (TFP Val. Position Sw.). The TFT Sensor is a resistor, or thermistor, which changes value based on temperature. The sensor has a negative-temperature coefficient. This means that as the temperature increases, the resistance decreases, and as the temperature decreases, the resistance increases. The Powertrain Control Module (PCM) supplies a 5 volt reference signal to the sensor on circuit 1227 and measures the voltage drop in the circuit. When the transmission fluid is cold, the sensor resistance is high and the PCM detects high signal voltage. As the fluid temperature warms to a normal operating temperature, the resistance becomes less and the signal voltage decreases. The PCM uses this information to control shift quality and torque converter clutch apply.
When the PCM detects a continuous open or short to power in the TFT signal circuit or the TFT Sensor, then DTC P0713 sets. DTC P0713 is a type D DTC.
Conditions for Setting the DTC
| • | The system voltage is 8-16 volts. |
| • | The ignition switch is in the RUN position. |
| • | The TFT Sensor indicates a signal voltage greater than 4.92 volts. |
| • | All conditions met for 409 seconds (6.8 minutes). |
Action Taken When the DTC Sets
| • | The PCM does not illuminate the Malfunction Indicator Lamp (MIL). |
| • | The PCM determines a default Transmission Fluid Temperature (TFT) using the following matrix: |
| Important: The actions listed below are in order of highest to lowest priority. |
| 1. | If any Engine Coolant Temperature (ECT) DTCs P0117 or P0118 are set, then the default TFT is equal to 135°C (275°F). |
| 2. | If the ECT is 125°C (257°F) or more, then the default TFT is equal to 135°C (275°F). |
| 3. | If the Engine Run Time is less than 300 seconds and: |
| • | No Intake Air Temperature (IAT) DTCs P0112 or P0113 are set and IAT is available, then the default TFT is equal to IAT. |
| • | Any Intake Air Temperature (IAT) DTCs P0112 or P0113 are set or IAT is NOT available, then the default TFT is equal to 90°C (194°F). |
| 4. | If the Engine Run Time is greater than 300 seconds and No Intake Air Temperature (IAT) DTCs P0112 or P0113 are set and IAT is available and Engine Coolant Temperature (ECT) is between 40 and 125°C (104 and 257°F) and: |
| • | IAT at startup is less than 15°C (59°F), then the default TFT is equal to the Engine Coolant Temperature (ECT) plus 5°C (8°F). |
| • | IAT at startup is greater than 35°C (95°F), then the default TFT is equal to the Engine Coolant Temperature (ECT) plus 10°C (16°F). |
| • | IAT at startup is between 15 and 35°C (59 and 95°F), then the default TFT is equal to the Engine Coolant Temperature (ECT). |
| 5. | If the Engine Run Time is greater than 300 seconds and any Intake Air Temperature (IAT) DTCs P0112 or P0113 are set or IAT is NOT available, then the default TFT is equal to the Engine Coolant Temperature (ECT). |
| 6. | If the Engine Run Time is greater than 300 seconds and ECT is less than 40°C (104°F) or more, then the default TFT is equal to 60°C (140°F). |
| • | The PCM freezes shift adapts from being updated. |
| • | DTC P0713 stores in PCM history. |
Conditions for Clearing the DTC
| • | A scan tool can clear the DTC from the PCM history. The PCM clears the DTC from the PCM history if the vehicle completes 40 warm-up cycles without a failure reported. |
| • | The PCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the PCM. |
Diagnostic Aids
| • | Inspect the wiring at the PCM, the transmission connector and all other circuit connecting points for the following conditions: |
| - | A bent terminal |
| - | A backed out terminal |
| - | A damaged terminal |
| - | Poor terminal tension |
| - | A chafed wire |
| - | A broken wire inside the insulation |
| - | Moisture intrusion |
| - | Corrosion |
| • | When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change. |
| • | Use the Temperature vs Resistance table when testing the TFT Sensor at various temperature levels. Test the TFT Sensor in order to evaluate the possibility of a skewed (mis-scaled) sensor. A skewed sensor can result in delayed garage shifts or TCC complaints. |
| • | The scan tool displays the transmission fluid temperature in degrees. After the transmission is operating, the fluid temperature should rise steadily to a normal operating temperature, then stabilize. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step verifies that a condition exists in the TFT Sensor circuit.
-
This step simulates a TFT Sensor DTC P0712. If the PCM recognizes high temperature, the PCM and wiring are functioning normally.
-
This step tests the TFT Sensor and Automatic Transmission Wiring Harness Assembly (A/T Wiring Harness Assembly).
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||
2 | Perform the transmission fluid checking procedure. Refer to Transmission Fluid Check . Have you performed the fluid checking procedure? | -- | Go to Transmission Fluid Check | |
Important: Before clearing the DTC(s), use the scan tool in order to record the Failure Records for reference. Using the Clear Info function will erase the stored Failure Records from the PCM. Does the scan tool display a TFT Sensor signal voltage greater than the specified value? | 4.92 volts | Go to Diagnostic Aids | ||
Does the TFT Sensor signal voltage drop to less than the specified value? | 0.2 volts | |||
Is the resistance within the specified range? | 3088-3942 Ohms at 20°C (68°F) 159-198 Ohms at 100°C (212°F) | Go to Diagnostic Aids | ||
6 | Inspect circuits 1227 (BRN) and 452 (GRY) of the Automatic Transmission Wiring Harness Assembly (A/T Wiring Harness Assembly) for an open condition. Refer to General Electrical Diagnosis . Did you find an open condition? | -- | ||
7 |
Is the resistance within the specified range? | 3088-3942 Ohms at 20°C (68°F) 159-198 Ohms at 100°C (212°F) | Go to Diagnostic Aids | |
8 | Replace the TFT Sensor (this is part of the TFP Val. Position Sw.). Refer to Valve Body and Pressure Switch Replacement . Is the replacement complete? | -- | -- | |
9 |
Refer to General Electrical Diagnosis . Did you find an open or shorted condition? | -- | ||
10 |
Refer to General Electrical Diagnosis . Did you find an open condition? | -- | ||
11 | Replace the A/T Wiring Harness Assembly. Is the replacement complete? | -- | -- | |
12 | Replace the PCM. Refer to Powertrain Control Module Replacement/Programming . Is the replacement complete? | -- | -- | |
13 | In order to verify your repair, perform the following procedure:
Has the test run and passed? | -- | System OK |
DTC P0713 Transmission Fluid Temperature (TFT) Sensor Circuit High Input 4.3L
Circuit Description
The Automatic Transmission Fluid Temperature (TFT) Sensor is part of the Automatic Transmission Fluid Pressure Manual Valve Position Switch (TFP Val. Position Sw.). The TFT Sensor is a resistor, or thermistor, which changes value based on temperature. The sensor has a negative-temperature coefficient. This means that as the temperature increases, the resistance decreases, and as the temperature decreases, the resistance increases. The Vehicle Control Module (VCM) supplies a 5 volt reference signal to the sensor on circuit 1227 and measures the voltage drop in the circuit. When the transmission fluid is cold, the sensor resistance is high and the VCM detects high signal voltage. As the fluid temperature warms to a normal operating temperature, the resistance becomes less and the signal voltage decreases. The VCM uses this information to control shift quality and torque converter clutch apply.
When the VCM detects a continuous open or short to power in the TFT signal circuit or the TFT Sensor, then DTC P0713 sets. DTC P0713 is a type D DTC.
Conditions for Setting the DTC
| • | The system voltage is 10-16 volts. |
| • | The ignition switch is in the RUN position. |
| • | The TFT Sensor indicates a signal voltage greater than 4.92 volts. |
| • | All conditions met for 409 seconds (6.8 minutes). |
Action Taken When the DTC Sets
| • | The VCM does not illuminate the Malfunction Indicator Lamp (MIL). |
| • | The VCM determines a default Transmission Fluid Temperature (TFT) using the following matrix: |
| The scan tool does not indicate the default TFT. |
| Important: The actions listed below are in order of highest to lowest priority. |
| 1. | If any Engine Coolant Temperature (ECT) DTCs P0117 or P0118 are set, then the default TFT is equal to 135°C (275°F). |
| 2. | If the ECT is 125°C (257°F) or more, then the default TFT is equal to 135°C (275°F). |
| 3. | If the Engine Run Time is less than 300 seconds and: |
| • | No Intake Air Temperature (IAT) DTCs P0112 or P0113 are set and IAT is available, then the default TFT is equal to IAT. |
| • | Any Intake Air Temperature (IAT) DTCs P0112 or P0113 are set or IAT is NOT available, then the default TFT is equal to 90°C (194°F). |
| 4. | If the Engine Run Time is greater than 300 seconds and No Intake Air Temperature (IAT) DTCs P0112 or P0113 are set and IAT is available and Engine Coolant Temperature (ECT) is between 40 and 125°C (104 and 257°F) and: |
| • | IAT at startup is less than 15°C (59°F), then the default TFT is equal to the Engine Coolant Temperature (ECT) plus 5°C (8°F). |
| • | IAT at startup is greater than 35°C (95°F), then the default TFT is equal to the Engine Coolant Temperature (ECT) plus 10°C (16°F). |
| • | IAT at startup is between 15 and 35°C (59 and 95°F), then the default TFT is equal to the Engine Coolant Temperature (ECT). |
| 5. | If the Engine Run Time is greater than 300 seconds and any Intake Air Temperature (IAT) DTCs P0112 or P0113 are set or IAT is NOT available, then the default TFT is equal to the Engine Coolant Temperature (ECT). |
| 6. | If the Engine Run Time is greater than 300 seconds and ECT is less than 40°C (104°F) or more, then the default TFT is equal to 60°C (140°F). |
| • | The VCM freezes shift adapts from being updated. |
| • | DTC P0713 stores in VCM history. |
Conditions for Clearing the DTC
| • | A scan tool can clear the DTC from the VCM history. The VCM clears the DTC from the VCM history if the vehicle completes 40 warm-up cycles without a failure reported. |
| • | The VCM cancels the DTC default actions when the fault no longer exists and the ignition is OFF long enough in order to power down the VCM. |
Diagnostic Aids
| • | Inspect the wiring at the VCM, the transmission connector and all other circuit connecting points for the following conditions: |
| - | A bent terminal |
| - | A backed out terminal |
| - | A damaged terminal |
| - | Poor terminal tension |
| - | A chafed wire |
| - | A broken wire inside the insulation |
| - | Moisture intrusion |
| - | Corrosion |
| • | When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change. |
| • | Use the Temperature vs Resistance table when testing the TFT Sensor at various temperature levels. Test the TFT Sensor in order to evaluate the possibility of a skewed (mis-scaled) sensor. A skewed sensor can result in delayed garage shifts or TCC complaints. |
| • | The scan tool displays the transmission fluid temperature in degrees. After the transmission is operating, the fluid temperature should rise steadily to a normal operating temperature, then stabilize. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step verifies a condition in the TFT Sensor circuit.
-
This step simulates a TFT Sensor DTC P0712. If the VCM recognizes low signal voltage (high temperature), the VCM and wiring are functioning normally.
-
This step tests the TFT Sensor and Automatic Transmission Wiring Harness Assembly (A/T Wiring Harness Assembly).
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||
2 | Perform the transmission fluid checking procedure. Refer to Transmission Fluid Check . Did you perform the fluid checking procedure? | -- | Go to Transmission Fluid Check | |
Important: Before clearing the DTC(s), use the scan tool in order to record the Failure Records for reference. Using the Clear Info function will erase the stored Failure Records from the VCM. Does the scan tool display a TFT Sensor signal voltage greater than the specified value? | 4.92 V | Go to Diagnostic Aids | ||
Does the TFT Sensor signal voltage drop to less than the specified value? | 0.2 V | |||
Is the resistance within the specified range? | 3088-3942 Ohms at 20°C (68°F) 159-198 Ohms at 100°C (212°F) | Go to Diagnostic Aids | ||
6 | Inspect circuits 1227 (BRN) and 452 (GRY) of the Automatic Transmission Wiring Harness Assembly (A/T Wiring Harness Assembly) for an open condition. Refer to General Electrical Diagnosis Procedures. Did you find an open condition? | -- | ||
7 |
Is the resistance within the specified range? | 3088-3942 Ohms at 20°C (68°F) 159-198 Ohms at 100°C (212°F) | Go to Diagnostic Aids | |
8 | Replace the TFT Sensor (this sensor is part of the TFP Val. Position Sw.). Refer to Valve Body and Pressure Switch Replacement. Is the replacement complete? | -- | -- | |
9 |
Refer to General Electrical Diagnosis Procedures. Did you find an open or short condition? | -- | ||
10 |
Refer to General Electrical Diagnosis Procedures. Did you find an open condition? | -- | ||
11 | Replace the A/T Wiring Harness Assembly. Refer to TCC PWM Solenoid, TCC Solenoid, and Wiring Harness Replacement. Is the replacement complete? | -- | -- | |
12 | Replace the VCM. Refer to VCM Replacement/Programming . Is the replacement complete? | -- | -- | |
13 | In order to verify your repair, perform the following procedure:
Has the test run and passed? | -- | System OK |
