Diagnosis
Use the following diagnostic table to diagnose the generator L circuit.
Use the following scan tool parameter when diagnosing the PCM controlled generator.
Generator L Terminal - Range Inactive/Active: The generator L terminal indicates whether the PCM is allowing the generator to operate. The PCM can disable the generator under certain conditions in order to ease starting. Active indicates that the PCM is allowing generator operation, while inactive indicates that the PCM is not allowing generator operation.Circuit Description
The generator communicates to the powertrain control module (PCM) over one line, the L or Lamp circuit. The PCM uses the L circuit to monitor faults in the charging system.
Diagnostic Aids
| • | An intermittent problem may be caused by a poor connection, rubbed through wire insulation, or a wire that is broken inside the insulation. |
| • | Any circuitry that is suspected as causing the intermittent complaint, should be thoroughly checked for the following items: |
| - | Improper mating |
| - | Broken locks |
| - | Poor terminal to wiring connections |
| - | Physical damage to the wiring harness |
Test Description
The numbers below refer to the step numbers on the Diagnostic Table.
-
The Powertrain OBD System Check prompts the technician to complete some basic checks and store the freeze frame and failure records data on the scan tool if applicable. This creates an electronic copy of the data taken when the malfunction occurred. The information is then stored on the scan tool for later reference.
-
If the volts telltale lamp is not operating, either a short circuit or the IPC is malfunctioning. This determines whether the L circuit, generator or IPC is malfunctioning.
-
If the charging system is not functioning, system voltage cannot be maintained above 12 V. Turning off all accessories assures that the system voltage is not being drawn down by an accessory that normally draws a large current.
-
Refer to Instrument Panel Cluster (IPC) Microprocessor portion of the service manual for replacement of the IPC.
-
If the lamp circuit is not shorted to ground, the volts telltale lamp will go OFF until the next key cycle when the test light is probed into terminal B. Be careful not to probe terminal C with the test light, this will turn off the volts telltale lamp whether or not the lamp circuit is shorted.
-
The PCM supplies a voltage to the generator. If voltage is available to the generator at this terminal, then the PCM and wiring are OK.
-
Program the replacement PCM. Perform the Crankshaft Position System Variation Learn Procedure. Refer to the latest Techline procedures for PCM programming.
-
If no malfunctions have been found at this point, refer to Diagnostic Aids for additional checks and information.
Step | Action | Value(s) | Yes | No | ||||
|---|---|---|---|---|---|---|---|---|
Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | |||||||
2 | Turn ON the ignition leaving the engine OFF. Is the volts telltale lamp on the IPC illuminated? | -- | ||||||
3 | Start the engine. Did the volts telltale lamp on the IPC turn OFF? | -- | ||||||
Is the volts telltale lamp illuminated on the IPC? | -- | |||||||
With the accessories OFF, install a scan tool. Does the voltage read more than the specified value? | 12V | |||||||
6 | With a test lamp connected to a ground, probe the lamp signal terminal of the generator harness connector. Does the test lamp illuminate? | -- | ||||||
Replace the Instrument Panel Cluster (IPC). Refer to Instrument Cluster Replacement in Instrument Panel, Gauges and Console. Is the action complete? | -- | -- | ||||||
Does the test lamp illuminate? | -- | |||||||
9 | Repair the short to voltage in the lamp circuit. Refer to Wiring Repairs in Wiring Systems. Is the action completed? | -- | -- | |||||
10 | Replace the generator. Refer to Generator Replacement in Engine Electrical. Is the action complete? | -- | -- | |||||
11 | Repair the short to ground in the lamp circuit. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |||||
Does the DMM read more than the specified value? | 4.5V | |||||||
13 | With the J 39200 DMM still connected to a ground, probe the battery terminal at the back of the generator. Does the DMM read the specified value? | B+ | ||||||
14 |
Was a repair necessary? | -- | ||||||
15 |
Is the action completed? | -- | -- | |||||
|
Important:: The replacement PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming . Replace the PCM.. Is the action completed? | -- | -- | ||||||
Operate the vehicle within the conditions under which the original symptom was noted. Does the system now operate properly? | -- | System OK |
