Battery Positive Cable Replacement 7.2L (CAT)
Important: When replacing battery cables, use a replacement cable that is the same type, diameter, and length. Additional feed wires may be attached to the positive cables. Additional ground leads may be attached to the negative
cables. Always route a replacement battery cable the same as the original cable routing.
Removal Procedure
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing
any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to
the vehicle or its components.
- Disconnect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
- Remove the positive cable from the starter solenoid.
- Remove the positive cable junction block .
- Remove the positive cable clamps and tie downs.
- Remove the positive cable.
Installation Procedure
- Install the positive cable to the original routing.
- Install the positive cable clamps and the tie downs.
Notice: Refer to Fastener Notice in the Preface section.
- Install the positive cable and the nut to the junction block .
Tighten
Tighten the positive cable to the Maxi-Fuse® block bolt to 11 N·m (97 lb in).
- Install the harness leads and the nuts to the starter solenoid.
Tighten
• | Tighten the positive cable starter nut to 10 N·m (89 lb in). |
• | Tighten the positive cable starter nut to 30 N·m (22 lb ft). |
- Connect the negative battery cable.
Tighten
• | Tighten the side post terminal bolt to 15 N·m (11 lb ft). |
• | Tighten the top post terminal nut to 17 N·m (13 lb ft). |
Battery Positive Cable Replacement 6.6L (LB7)
Removal Procedure
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing
any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to
the vehicle or its components.
Important: When replacing the battery cables, use a
replacement cable that is the same type diameter and length. Additional feed wires
may be attached to the positive cables. Additional ground leads may be attached to
the negative cables. Always route a replacement battery cable the same as the original
cable routing.
- Disconnect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
- Unsnap the positive battery cable cap.
- Loosen the positive battery cable.
- Remove the positive battery cable.
- Unsnap the junction block cover.
- Remove the positive cable (2) from the junction block.
- Remove the battery cable channel bolts.
- Release the tabs on the channel.
- Remove the battery cable from the channel.
- Remove the battery cable retainer nut and
the retainer.
- Remove the battery positive cable from the retainer.
- Remove the starter lead nut.
- Remove the positive cable from the starter.
- Remove the positive battery cable.
Installation Procedure
- Install the positive cable to the vehicle.
- Install the positive cable to the starter.
Notice: Refer to Fastener Notice in the Preface section.
- Install the starter lead nut.
Tighten
Tighten the nut to 10 N·m (89 lb in).
- Install the battery positive cable in the
retainer.
- Install the positive cable retainer and nut.
Tighten
Tighten the nut to 12 N·m (106 lb in).
- Install the battery positive cable to the frame channel.
- Install the battery cable channel bolts.
Tighten
Tighten the bolts to 8 N·m (71 lb in).
- Install the negative cable clip to the clip on the positive cable.
- Install the positive cable (2) onto
the junction block stud with nut.
Tighten
Tighten the positive cable nut to the Maxi-Fuse
block stud to 11 N·m (97 lb in).
- Snap the junction block cover closed.
- Install the positive battery cable.
- Tighten the positive battery cable.
Tighten
Tighten the bolt to 17 N·m (13 lb ft).
- Snap the positive battery cable cap closed.
- Connect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
Battery Positive Cable Replacement 6.6L (LLY)
Removal Procedure
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing
any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to
the vehicle or its components.
- Disconnect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
- Unsnap the positive battery cable cap.
- Disconnect the positive battery cable.
- Unsnap the junction block cover.
- Remove the positive cable (2) from the junction block.
- Remove the clip attaching the positive cable to the negative cable.
- Remove the battery cable channel bolts.
- Remove the battery cable from the channel.
- Remove the battery cable retainer nut (6)
and the retainer.
- Remove the battery positive cable from the retainer.
- Remove the positive battery cable nut (7).
- Remove the positive battery cable lead (8) from the starter.
- Remove the positive battery cable.
Installation Procedure
- Install the positive battery cable.
Notice: Refer to Fastener Notice in the Preface section.
- Install the positive battery cable lead (8) to the starter.
- Install the positive battery cable nut (7).
Tighten
Tighten the nut to 9 N·m (80 lb in).
- Install the battery positive cable to the retainer.
- Install the battery cable retainer nut (6) and the retainer.
Tighten
Tighten the nut to 12 N·m (106 lb in).
- Install the battery cable to the channel.
- Install the battery cable channel bolts.
Tighten
Tighten the bolts to 8 N·m (71 lb in).
- Install the clip attaching the positive cable to the negative cable.
- Install the positive cable (2) to the junction
block.
- Snap the junction block cover closed.
- Tighten the positive cable nut.
Tighten
Tighten the positive cable nut to the Maxi-Fuse junction block bolt to 11 N·m
(97 lb in).
- Snap the positive battery cable cap closed.
- Connect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.