GM Service Manual Online
For 1990-2009 cars only

Starter Replacement LG4

Removal Procedure

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

  2. Object Number: 826460  Size: SH
  3. Disconnect the electrical connectors from the starter motor.
  4. Remove the nuts and the washers that attach the starter motor to the engine.

  5. Object Number: 826461  Size: SH
  6. Remove the starter motor from the engine.
  7. Clean the following components:
  8. • The starter motor terminals
    • The electrical connectors
  9. Inspect the pinion gear teeth for wear and damage.

Installation Procedure


    Object Number: 826461  Size: SH
  1. Connect the starter motor to the engine.
  2. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 826460  Size: SH
  3. Install the nuts and the washers that attach the starter motor to the engine.
  4. Tighten
    Tighten the starter motor mounting nuts to 82 N·m (60 lb ft).

  5. Connect the electrical connectors to the starter motor.
  6. Hold the hex-shaped base of the stud while tightening the positive battery cable nut.
  7. Tighten

    1. Tighten the positive battery cable nut to 21 N·m (16 lb ft).
    2. Tighten the solenoid bolt to 3.4 N·m (30 lb in).

    Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Starter Replacement LG5

Removal Procedure


    Object Number: 214989  Size: SH

    Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the starter ground cable from the starter. Refer to Battery Negative Cable Replacement .
  3. Remove the electrical connectors from the starter motor.
  4. Remove the starter motor bolts.
  5. Remove the starter motor from the engine.
  6. Clean the following components:
  7. • The starter motor solenoid terminals
    • The electrical connector terminals
  8. Inspect the starter ring gear teeth for wear and damage.

Installation Procedure


    Object Number: 214989  Size: SH
  1. Install the starter motor to the engine.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the starter motor bolts.
  4. Tighten
    Tighten the starter motor bolts to 70 N·m (52 lb ft).

  5. Install the electrical connectors to the starter motor.
  6. Tighten

        • Tighten the battery positive cable nut to 30 N·m (22 lb ft).
        • Tighten the starter solenoid nut to 3 N·m (27 lb in).
  7. Install the starter ground cable. Refer to Battery Negative Cable Replacement .
  8. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Starter Replacement L18

Removal Procedure

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Raise and suitably support the vehicle with safety stands. Refer to Lifting and Jacking the Vehicle .

  3. Object Number: 1857726  Size: SH
  4. Remove the starter heat shield and extension shield (C42 only) nuts (1, 2) and shields.

  5. Object Number: 742250  Size: SH
  6. Remove the starter motor solenoid lead nuts.
  7. If equipped with a automatic transmission, remove the positive cable and engine harness leads from the starter solenoid.

  8. Object Number: 742251  Size: SH
  9. If equipped with a manual transmission, remove the positive cable and engine harness lead from the starter solenoid.

  10. Object Number: 742244  Size: SH
  11. If equipped with a automatic transmission, remove the starter motor bolts.

  12. Object Number: 742243  Size: SH
  13. If equipped with a manual transmission, remove the starter motor bolts.
  14. Remove the starter motor.

Installation Procedure


    Object Number: 742243  Size: SH
  1. Install the starter motor.
  2. Notice: Refer to Fastener Notice in the Preface section.

  3. If equipped with a manual transmission, install the starter motor bolts.
  4. Tighten
    Tighten the starter motor bolts to 67 N·m (49 lb ft).


    Object Number: 742244  Size: SH
  5. If equipped with a automatic transmission, install the starter motor bolts.
  6. Tighten
    Tighten the starter motor bolts to 50 N·m (37 lb ft).


    Object Number: 742251  Size: SH
  7. If equipped with a manual transmission, install the positive cable and engine harness lead to the starter solenoid.

  8. Object Number: 742250  Size: SH
  9. If equipped with a automatic transmission, install the positive cable and engine harness leads to the starter solenoid.
  10. Install the starter motor solenoid lead nuts.
  11. Tighten

        • Tighten the positive cable nut to 10 N·m (89 lb in).
        • Tighten the harness lead nut to 2 N·m (18 lb in).

    Object Number: 1857726  Size: SH
  12. Install the starter heat shield and extension shield (C42) to the starter and engine.
  13. Tighten

        • Tighten the shield nuts (1, 2) to 3 N·m (35 lb in).
        • Tighten the harness lead nuts to 5 N·m (44 lb in).
  14. Lower the vehicle.
  15. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Starter Replacement LB7

Removal Procedure

  1. Disconnect both battery negative cables. Refer to Battery Negative Cable Disconnection and Connection .
  2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

  3. Object Number: 674619  Size: SH
  4. Remove the battery positive cable from the starter motor.
  5. Remove the solenoid wires.

  6. Object Number: 660305  Size: SH
  7. Remove the starter motor bolts.
  8. Remove the starter motor assembly.

Installation Procedure


    Object Number: 660305  Size: SH
  1. Install the starter motor to the engine rear cover.
  2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  3. Install the starter motor bolts.
  4. Tighten
    Tighten the starter bolts to 78 N·m (58 lb ft).


    Object Number: 674619  Size: SH
  5. Install the solenoid wires.
  6. Install the starter solenoid nut.
  7. Tighten
    Tighten the starter solenoid nut to 3.4 N·m (30 lb in).

  8. Install the battery positive cable to the solenoid stud.
  9. Install the battery positive cable nut.
  10. Tighten
    Tighten the starter battery positive cable nut to 9 N·m (80 lb in).

  11. Lower the vehicle.
  12. Connect both battery negative cables. Refer to Battery Negative Cable Disconnection and Connection .

Starter Replacement 6.6L (LLY)

Removal Procedure

    Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

  2. Object Number: 1369542  Size: SH
  3. Remove the engine wiring harness nut (4).
  4. Remove the engine wiring harness lead (1) from the starter.

  5. Object Number: 1369543  Size: SH
  6. Remove the positive battery cable nut (7).
  7. Remove the positive battery cable lead (8) from the starter.

  8. Object Number: 1334814  Size: SH
  9. Remove the starter motor bolts.
  10. Remove the starter motor.

Installation Procedure

    Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1334814  Size: SH
  1. Install the starter motor.
  2. Install the starter motor bolts.
  3. Tighten
    Tighten the bolts to 78 N·m (58 lb ft).


    Object Number: 1369543  Size: SH
  4. Install the positive battery cable lead (8) to the starter.
  5. Install the positive battery cable nut (7).
  6. Tighten
    Tighten the nut to 9 N·m (80 lb in).


    Object Number: 1369542  Size: SH
  7. Install the engine wiring harness lead (1) to the starter.
  8. Install the engine wiring harness nut (4).
  9. Tighten
    Tighten the nut to 3.4 N·m (30 lb in).

  10. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Starter Replacement 8.1L

Removal Procedure

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

  2. Object Number: 747162  Size: SH
  3. Remove the starter heat shield bolts, nut, and shield, if necessary.

  4. Object Number: 751548  Size: SH
  5. Remove the positive cable nut.
  6. Remove the positive cable from the starter solenoid.

  7. Object Number: 750961  Size: SH
  8. Remove the engine harness ground nut from the starter solenoid.
  9. Remove the engine harness ground (4) from the starter solenoid.

  10. Object Number: 747161  Size: SH
  11. Remove the starter motor bolts.
  12. Remove the starter motor.

Installation Procedure


    Object Number: 747161  Size: SH
  1. Install the starter motor.
  2. Notice: Refer to Fastener Notice in the Preface section.

  3. Install the starter motor bolts.
  4. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).


    Object Number: 750961  Size: SH
  5. Install the engine harness ground (4) to the starter solenoid.
  6. Install the starter solenoid nut.
  7. Tighten
    Tighten the nut to 3.4 N·m (30 lb in).


    Object Number: 751548  Size: SH
  8. Install the positive cable to the starter solenoid.
  9. Install the starter lead nut.
  10. Tighten
    Tighten the nut to 9 N·m (80 lb in).


    Object Number: 747162  Size: SH
  11. Install the starter heat shield, nut and bolts, if necessary.
  12. Tighten

        • Tighten the bolts to 3 N·m (35 lb in).
        • Tighten the nut to 5 N·m (44 lb in).
  13. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .