GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

  1. Recover the refrigerant from the A/C system. Refer to Refrigerant Recovery and Recharging .
  2. Remove the right wheelhouse panel. Refer to Wheelhouse Panel Replacement in Body Front End.
  3. Remove the air cleaner layer. Refer to the appropriate procedure:
  4. •  Air Cleaner Replacement in Engine Controls-6.6L.
    •  Air Cleaner Replacement in Engine Controls-8.1L.
    •  Air Cleaner Replacement in Engine Controls-7.8L.
    • Caterpillar® 3126 Unit Repair Manual
  5. Disconnect the low pressure sensor electrical connector.
  6. Disconnect the blower motor electrical connector.
  7. Disconnect the blower motor resistor assembly electrical connector.

  8. Object Number: 769765  Size: SH
  9. Remove the evaporator outlet hose retaining nuts (4, 5).

  10. Object Number: 769799  Size: SH
  11. Remove the compressor inlet hose retaining nut (2).

  12. Object Number: 769756  Size: SH
  13. Remove the retaining nuts (3) from the accumulator retaining bracket.
  14. Remove the accumulator (5) from the bracket.
  15. Remove the multi-use module bracket. Refer to the appropriate procedure:
  16. •  Multiuse Module Bracket Replacement in Engine Controls-6.6L.
    •  Multiuse Module Bracket Replacement in Engine Controls-8.1L.
    •  Multiuse Module Bracket Replacement in Engine Controls-7.8L.
    • Caterpillar® 3126 Unit Repair Manual

    Object Number: 800358  Size: SH
  17. Remove the retaining nut (3)from the evaporator inlet tube (5).
  18. Remove the evaporator inlet tube from the evaporator.
  19. Remove the sealing washers.

  20. Object Number: 694201  Size: SH
  21. Remove the screws (2) from the evaporator and blower module assembly.
  22. Remove the evaporator and blower module assembly front cover (3).
  23. Remove the recirculation door actuator (7) and the linkage.

Installation Procedure


    Object Number: 694201  Size: SH
  1. Install the recirculation door actuator (7) and the linkage.
  2. Install the evaporator and blower module assembly cover (3).
  3. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  4. Install the screws.
  5. Tighten
    Tighten the screws to 1.9 N·m (17 lb in).

  6. Install new sealing washers to the evaporator inlet and outlet tubes. Refer to Sealing Washer Replacement .

  7. Object Number: 800358  Size: SH
  8. Install the evaporator inlet tube (4) to the evaporator.
  9. Install the evaporator inlet tube retaining nut (3).
  10. Tighten
    Tighten the nut to 16 N·m (12 lb ft).

  11. Install the multi-use module bracket. Refer to the appropriate procedure:
  12. •  Multiuse Module Bracket Replacement in Engine Controls-6.6L.
    •  Multiuse Module Bracket Replacement in Engine Controls-8.1L.
    •  Multiuse Module Bracket Replacement in Engine Controls-7.8L.
    • Caterpillar® 3126 Unit Repair Manual

    Object Number: 769756  Size: SH
  13. Install the accumulator (5) to the bracket.
  14. Install the nuts (3) to the accumulator retaining bracket.
  15. Tighten
    Tighten the nuts to 9 N·m (80 lb in).


    Object Number: 769799  Size: SH
  16. Install the compressor inlet hose and retaining nut (2) to the accumulator.
  17. Tighten
    Tighten the nut to 16 N·m (12 lb ft).


    Object Number: 769765  Size: SH
  18. Install the evaporator outlet hose and retaining nuts (4,5).
  19. Tighten
    Tighten the nut to 18 N·m (13 lb ft).

  20. Connect the low pressure sensor electrical connector.
  21. Connect the blower motor electrical connector.
  22. Connect the blower motor resistor assembly electrical connector.
  23. Install the air cleaner layer. Refer to the appropriate procedure:
  24. •  Air Cleaner Replacement in Engine Controls-6.6L.
    •  Air Cleaner Replacement in Engine Controls-8.1L.
    •  Air Cleaner Replacement in Engine Controls-7.8L.
    • Caterpillar® 3126 Unit Repair Manual
  25. Install the right wheelhouse panel. Refer to Wheelhouse Panel Replacement in Body Front End.
  26. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging .