GM Service Manual Online
For 1990-2009 cars only

DTC P0833 8.1L


Object Number: 1499382  Size: LF
Master Electrical Component List
Manual Transmission Schematics
OBD II Symbol Description Notice

Circuit Description

Battery voltage is supplied from the brake fuse to the clutch switch. The clutch switch is a normally-closed switch. When the clutch pedal is released, the clutch pedal position (CPP) switch signal circuit is pulled up to B+. When the clutch pedal is applied, the switch opens and the voltage drops to 0 volts.

When the powertrain control module (PCM) detects a large number of gear changes without detecting a clutch switch transition, DTC P0833 sets. DTC P0833 is a type B DTC.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0833 Clutch Pedal Switch 2 Circuit

Conditions for Running the DTC

No VSS DTC P0500.

Conditions for Setting the DTC

The PCM detects 7 changes in vehicle speed greater than 38 km/h (24 mph) without the PCM detecting a clutch pedal transition.

Action Taken When the DTC Sets

    • The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.
    • The PCM disables cruise control.
    • The PCM disables power take-off.
    • The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records.
    • The PCM stores DTC P0833 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

Conditions for Clearing the MIL/DTC

    • The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.
    • A scan tool can clear the MIL/DTC.
    • The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.
    • The PCM cancels the DTC default actions when the ignition switch is OFF long enough in order to power down the PCM.

Step

Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Use the scan tool to monitor the clutch pedal position switch parameter.
  4. Apply and release the clutch pedal several times.

Does the scan tool indicate a change in state when the clutch pedal is either applied or released?

--

Go to Intermittent Conditions in Engine Controls - 8.1L

Go to Step 3

3

Inspect the adjustment of the CPP switch. Refer to Clutch Pedal Position Switch Replacement in Clutch.

Did you find and correct a condition?

--

Go to Step 14

Go to Step 4

4

  1. Turn OFF the ignition.
  2. Caution: Refer to SIR Caution in the Preface section.

  3. Disconnect the CPP switch connector.
  4. Measure the voltage between ignition 3 voltage circuit of the CPP switch harness connector and ground.

Does the DMM indicate the specified value?

B+

Go to Step 5

Go to Step 11

5

  1. Connect a fused jumper wire between the ignition 3 voltage circuit and the CPP switch signal circuit of the CPP switch harness connector.
  2. Turn ON the ignition, with the engine OFF.
  3. Use the scan tool to monitor the clutch pedal position switch parameter.

Does the scan tool display that the clutch is released?

--

Go to Step 8

Go to Step 6

6

  1. Turn OFF the ignition.
  2. Disconnect the CPP switch signal at the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
  3. Use the DMM to test for continuity on the CPP switch signal circuit between the CPP switch harness connector and the PCM. Refer to Testing for Continuity in Wiring Systems.

Did you detect continuity?

--

Go to Step 7

Go to Step 10

7

Use the DMM to test for continuity between the CPP switch signal circuit of the CPP switch harness connector and ground. Refer to Testing for Continuity in Wiring Systems.

Did you detect continuity?

--

Go to Step 10

Go to Step 9

8

  1. Inspect for a loose connection at the CPP switch connector. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
  2. Repair the condition as necessary. Refer to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 12

9

  1. Inspect for a loose connection at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
  2. Repair the condition as necessary. Refer to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 13

10

Repair the open or short to ground in the CPP switch signal circuit. Refer to Wiring Repairs in Wiring Systems.

Is the action complete?

--

Go to Step 14

--

11

Repair the open in the CPP switch feed circuit. Refer to Wiring Repairs in Wiring Systems.

Is the action complete?

--

Go to Step 14

--

12

Replace the CPP switch. Refer to Clutch Pedal Position Switch Replacement in Clutch.

Is the action complete?

--

Go to Step 14

--

13

Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Is the action complete?

--

Go to Step 14

--

14

  1. Select the DTC.
  2. Select Clear Info.
  3. Operate the vehicle from 0 km/h (0 mph) to above 38 km/h (24 mph) then back to 0 km/h (0 mph) 7 times.
  4. Select Specific DTC.
  5. Enter DTC P0833.

Has the test run and passed?

--

Go to Step 15

Go to Step 2

15

With the scan tool, observe the stored information, capture info and DTC info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information

System OK

DTC P0833 6.6L


Object Number: 1499384  Size: LF
Master Electrical Component List
Manual Transmission Schematics
OBD II Symbol Description Notice

Circuit Description

Battery voltage is supplied from the brake fuse to the clutch switch. The clutch switch is a normally-closed switch. When the clutch pedal is released, the clutch pedal position (CPP) switch signal circuit is pulled up to B+. When the clutch pedal is applied, the switch opens and the voltage drops to 0 volts.

When the engine control module (ECM) detects a large number of gear changes without detecting a clutch switch transition, DTC P0833 sets. DTC P0833 is a type C DTC.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0833 Clutch Pedal Switch 2 Circuit

Conditions for Running the DTC

No VSS DTC P0500.

Conditions for Setting the DTC

The ECM detects 7 changes in vehicle speed from 0 km/h (0 mph) to above 38 km/h (24 mph) and then back to 0 km/h (0 mph) without the ECM detecting a clutch pedal transition.

Action Taken When the DTC Sets

    •  The ECM does not illuminate the malfunction indicator lamp (MIL).
    • The ECM disables cruise control.
    • The ECM disables power take-off.
    • The ECM records the operating conditions when the Conditions for Setting the DTC are met. The ECM stores this information as Failure Records.
    • The ECM stores DTC P0833 in ECM history.

Conditions for Clearing the DTC

    • A scan tool can clear the DTC.
    • The ECM clears the DTC from ECM history if the vehicle completes 40 warm-up cycles without a non-emission-related diagnostic fault occurring.
    • The ECM cancels the DTC default actions when the ignition switch is OFF long enough in order to power down the ECM.

Step

Action

Value(s)

Yes

No

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Use the scan tool to monitor the clutch pedal position switch parameter.
  4. Apply and release the clutch pedal several times.

Does the scan tool indicate a change in state when the clutch pedal is either applied or released?

--

Go to Intermittent Conditions in Engine Controls - 6.6L

Go to Step 3

3

Inspect the adjustment of the CPP switch. Refer to Clutch Pedal Position Switch Replacement in Clutch.

Did you find and correct a condition?

--

Go to Step 14

Go to Step 4

4

  1. Turn OFF the ignition.
  2. Caution: Refer to SIR Caution in the Preface section.

  3. Disconnect the CPP switch connector.
  4. Measure the voltage between the ignition 3 voltage circuit of the CPP switch harness connector and ground.

Does the DMM indicate the specified value?

B+

Go to Step 5

Go to Step 11

5

  1. Connect a fused jumper wire between the ignition 3 voltage circuit and the CPP switch signal of the CPP switch harness connector.
  2. Turn ON the ignition, with the engine OFF.
  3. Use the scan tool to monitor the clutch pedal position switch parameter.

Does the scan tool display that the clutch is released?

--

Go to Step 8

Go to Step 6

6

  1. Turn OFF the ignition.
  2. Disconnect the CPP switch signal of the ECM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
  3. Use the DMM to test for continuity on the CPP switch signal circuit between the CPP switch harness connector and the ECM. Refer to Testing for Continuity in Wiring Systems.

Did you detect continuity?

--

Go to Step 7

Go to Step 10

7

Use the DMM to test for continuity between the CPP switch signal circuit of the CPP switch harness connector and ground. Refer to Testing for Continuity in Wiring Systems.

Did you detect continuity?

--

Go to Step 10

Go to Step 9

8

  1. Inspect for a loose connection at the CPP switch connector. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
  2. Repair the condition as necessary. Refer to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 12

9

  1. Inspect for a loose connection at the ECM. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
  2. Repair the condition as necessary. Refer to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 13

10

Repair the open or short to ground in the CPP switch signal circuit. Refer to Wiring Repairs in Wiring Systems.

Is the action complete?

--

Go to Step 14

--

11

Repair the open in the CPP switch feed circuit. Refer to Wiring Repairs in Wiring Systems.

Is the action complete?

--

Go to Step 14

--

12

Replace the CPP switch. Refer to Clutch Pedal Position Switch Replacement in Clutch.

Is the action complete?

--

Go to Step 14

--

13

Replace the ECM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Is the action complete?

--

Go to Step 14

--

14

  1. Select the DTC.
  2. Select Clear Info.
  3. Operate the vehicle from 0 km/h (0 mph) to above 38 km/h (24 mph) then back to 0 km/h (0 mph) 7 times.
  4. Select Specific DTC.
  5. Enter DTC P0833.

Has the test run and passed?

--

Go to Step 15

Go to Step 2

15

With the scan tool, observe the stored information, capture info and DTC info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information

System OK