Notice: If the power steering system has been serviced, an accurate fluid level reading cannot be obtained unless air is bled from the steering system. The air in the fluid may cause pump cavitation noise and may cause pump damage over a period of time.

Important: 

DEFINITION: The Power Steering System Test Procedure will perform the following functions:

Inspect the power steering fluid for the following indications of contamination:

Is the fluid free of contamination?

--

Go to Step 3

Go to Step 2

Flush the power steering system. Refer to Power Steering System Flushing .

Did you complete the procedure?

--

Go to Step 3

--

Important: In order to accurately diagnose the system, the malfunction must be present during the test procedure.

Attempt to duplicate the condition.

Is the condition present?

--

Go to Step 4

System OK

1. Turn the ignition switch to the OFF position.
2. Place a drain pan under the vehicle in order to catch any power steering fluid.

Important: When hooking up the power steering analyzer it may be necessary to disassemble adapters and reassemble them reversed to obtain proper hook-up. If the power steering analyzer is hooked up backwards there will be a pressure reading but no flow.

3. Disconnect the power steering pressure pipe/hose from the power steering pump or the power steering gear as necessary.
4. Install the J 44721 Power Steering System Analyzer between the power steering pump and the power steering gear on the pressure side. Adapters may be required.
5. Fill the power steering system. Refer to Checking and Adding Power Steering Fluid .

Did you complete the installation?

--

Go to Step 5

--

5

1. Fully open the J 44721 valve.
2. Start the engine.

Notice: Do not hold the steering wheel in the full turn position longer than 5 seconds, as damage to the steering pump may result.

3. Turn the steering wheel and BRIEFLY hold the steering wheel against the steering stop in order to release any trapped air from the system.
4. Inspect and ensure that all of the power steering pipe/hose connections are not leaking.
5. Making sure the steering wheel is OFF the steering stop, observe the pressure reading.

Is the pressure reading greater than the specified value?

1 379 kPa

(230 psi)

Go to Step 6

Go to Step 7

Important: A restriction may be present in the power steering system. Turn off the engine IMMEDIATELY.

Locate and repair the restriction.

Did you complete the repair?

--

Go to Step 15

--

7

1. Allow the engine to run until the engine reaches full operating temperature.
2. Record the pressure reading and flow reading.
3. Partially close the J 44721 valve until the system pressure reaches the specified value, then record the FLOW reading.
4. Subtract second flow reading from the first flow reading.

Is the flow DECREASE greater than 3.8 L (1 gal) per minute?

4 827 kPa

(700 psi)

Go to Step 11

Go to Step 8

8

Notice: Do not leave the valve fully closed for more than 5 seconds, or the pump could be damaged internally.

Fully close then open the J 44721 valve 3 times. Record all of the high pressure readings. Refer to Power Steering Pump Specifications for power steering system pressure relief specifications.

Are the three high pressure readings within specifications?

--

Go to Step 9

Go to Step 13

Are the three high pressure readings within 245 kPa (50 psi) of each other?

--

Go to Step 10

Go to Step 13

10

1. Increase the engine speed to approximately 1,500 RPM.
2. Record the flow reading. Refer to Power Steering Pump Specifications for power steering system pressure specifications.

Is the actual flow reading within specifications?

--

Go to Step 11

Go to Step 13

Is the difference between the actual flow reading and the maximum flow specification more than 3.8 L (1 gal) per minute?

--

Go to Step 13

Go to Step 12

12

Notice: Do not hold the steering wheel in the full turn position longer than 5 seconds, as damage to the steering pump may result.

Turn the steering wheel from steering stop to steering stop and record the PRESSURE readings at each stop.

Does the pressure increase to over 6 895 kPa (1,000 psi)?

--

Go to Step 15

Go to Step 14

Replace the power steering pump. Refer to Power Steering Pump Replacement .

Did you complete the replacement?

--

Go to Step 15

--

The power steering gear is leaking across the piston or bypassing the valve circuit. Replace the power steering gear. Refer to Steering Gear Replacement .

Did you complete the replacement?

--

Go to Step 15

--

Test the power steering system for the original condition.

Does the original condition still exist?

--

Go to Step 5

Go to Step 16

1. Disconnect and remove the J 44721 from the vehicle.
2. Connect the vehicle power steering pipes/hoses.
3. Fill the power steering system. Refer to Checking and Adding Power Steering Fluid .

Did you complete the procedure?

--

System OK

--