GM Service Manual Online
For 1990-2009 cars only

Brake Caliper Overhaul Fixed Mount

Warning: Refer to Brake Dust Warning in the Preface section.

Warning: Refer to Brake Fluid Irritant Warning in the Preface section.

Disassembly Procedure

Caution: Do not loosen or remove the four bolts in the brake caliper bridge area. The brake caliper bridge bolts may become loose. If the bridge bolts become loose, replace the brake caliper. Failure to follow these instructions will cause damage to the brake caliper.

  1. Remove the brake fluid from the brake caliper.
  2. Clean the exterior of the brake caliper. Use denatured alcohol or suitable, non-petroleum based solvent.

  3. Object Number: 200270  Size: SH
  4. Remove the heat shields.
  5. Place a block of wood equal to the length of the brake pad lining inside the caliper bridge area between the pistons.

  6. Object Number: 171564  Size: SH

    Warning: Do not place your fingers in front of the piston in an attempt to catch or protect it when applying compressed air. This could result in serious injury.

    Caution: Use only enough air to ease the piston out of the bore. If the piston is blown out, even with the padding, it can be damaged.

  7. Direct compressed air in to caliper brake fluid inlet in order to remove the pistons from the caliper bore.
  8. Use just enough air to ease the pistons out. Do not use more than 620 kPa (90 psi).

    5.1. If only some of the pistons are removed, partially reinsert the pistons.
    5.2. Block the reinserted pistons in place.
    5.3. Apply air pressure again in order to remove the remaining pistons.
  9. Remove the dust boots using a screwdriver.

  10. Object Number: 171569  Size: SH
  11. Remove the piston seals from the groove in the caliper bore using a pointed piece of wood or plastic.
  12. Remove the brake caliper bleeder valves.
  13. Caution: Do not use mineral base cleaning solvents such as gasoline, kerosene, carbon tetrachloride, acetone, or paint thinner to clean the brake caliper. These solvents will cause rubber parts to become soft and swollen in an extremely short time.

  14. Clean all of the parts in denatured alcohol or suitable, non-petroleum based solvent.
  15. Blow out all of the passages in the brake caliper housing and the brake caliper bleeder valve.
  16. Use dry, filtered, non-lubricated compressed air.

  17. Clean the brake caliper support rail surfaces with a wire brush.
  18. Inspect the support rail surfaces for rust or corrosion.
  19. Inspect the brake caliper housing for cracks or other damage. Replace the caliper housing if necessary.
  20. Inspect the outside diameter of the pistons. Replace the faulty pistons if you find any of the following conditions:
  21. • Scoring
    • Nicks
    • Corrosion
    • Wear
    • Any other damage

    Note: The outside diameter of the piston is the primary sealing surface of the brake caliper. The piston diameter is manufactured to very close tolerances. Do not refinish the piston diameter. Do not use abrasives on the piston diameter.

  22. If you find any surface faults, replace the piston.
  23. Inspect the caliper bore. Replace the caliper if you find any of the following conditions:
  24. • Scoring
    • Nicks
    • Corrosion
    • Wear
    • Any other damage

    Note: Do not use any abrasive on the caliper bore, including emery cloth.

  25. Polish out stains and minor corrosion from the caliper bore with crocus cloth.
  26. If you cannot remove the stains and corrosion with crocus cloth, replace the caliper.

  27. Clean the caliper bore after using the crocus cloth.

Assembly Procedure

  1. Place the brake caliper housing on a clean work bench with the open ends of the caliper bores facing up.
  2. Dip the piston seals in clean brake fluid.

  3. Object Number: 200270  Size: SH
  4. Gently work the piston seal around the seal groove of each caliper bore with a finger.
  5. Ensure that the seal is fully seated in the groove.
  6. Ensure that the piston seal is not twisted or rolled in the groove.
  7. Lubricate the pistons and the caliper bores with clean brake fluid.
  8. Gently push the piston into the caliper bore.
  9. Rotate the piston slightly in order to prevent dislodging the piston seal.
  10. Push the piston to the bottom of the caliper bore.
  11. Press the new dust boot into the counterbore in the brake caliper housing.
  12. The dust boot overlaps the stepped edge of the piston.

  13. Install a new heat shield on the piston.
  14. 11.1. Align the slots with the castellations on the piston.
    11.2. Press down until the 4 fingers for the heat shield engage the piston inside wall.

    Caution: Refer to Fastener Caution in the Preface section.

  15. Install the brake caliper bleeder valve.
  16. Tighten
    Tighten the valve to 17 N·m (13 lb ft).

Brake Caliper Overhaul TRW - Pin Slider

Warning: Refer to Brake Dust Warning in the Preface section.

Warning: Refer to Brake Fluid Irritant Warning in the Preface section.

Disassembly Procedure

  1. Remove the brake fluid from the brake caliper.
  2. Clean the exterior of the brake caliper.

  3. Object Number: 171564  Size: SH
  4. Pad the exterior of the brake caliper with a clean shop towel.
  5. Warning: Refer to Safety Glasses and Compressed Air Warning in the Preface section.

  6. Direct compressed air in to the caliper brake fluid inlet in order to remove the pistons from the caliper bore.
  7. 4.1. If only one piston leaves the bore, reinsert the piston part-way.
    4.2. Block the reinserted piston in place.
    4.3. Apply air pressure again. This should free the remaining piston.

    Object Number: 1533621  Size: SH
  8. Remove the dust boots (1).

  9. Object Number: 171569  Size: SH
  10. Remove the piston seals from the groove in the caliper bore using a pointed plastic.
  11. Remove the brake caliper bleeder valve.

  12. Object Number: 1533621  Size: SH
  13. Clean all of the parts using denatured alcohol or an equivalent approved brake cleaner, or brake fluid GM P/N 12377967 (Canadian P/N 992667) or equivalent.
  14. Blow out all of the passages in the brake caliper housing (4) and the brake caliper bleeder valve.
  15. Use dry, filtered, unlubricated compressed air.

  16. Clean the brake caliper support rail surfaces with a wire brush.
  17. Inspect the support rail surfaces for rust or corrosion.
  18. Inspect the brake caliper housing for cracks or other damage. Replace the caliper housing if necessary.
  19. Inspect the outside diameter of the pistons for the following conditions:
  20. • Scoring
    • Nicks
    • Corrosion
    • Wear
    • Any other damage

    Note: The outside diameter of the piston is the primary sealing surface of the brake caliper. The piston diameter is manufactured to very close tolerances. Do not refinish the piston diameter. Do not use abrasives on the piston diameter.

  21. If you find any surface faults, replace the piston.
  22. Inspect the caliper bore for the following conditions:
  23. • Scoring
    • Nicks
    • Corrosion
    • Wear
    • Any other damage

    Note: Do not use any abrasive on the caliper bore, including emery cloth.

  24. Polish out stains and minor corrosion from the caliper bore with crocus cloth.
  25. If you cannot remove the stains and corrosion with crocus cloth, replace the caliper.

  26. Clean the caliper bore after using the crocus cloth.

Assembly Procedure

  1. Place the brake caliper housing on a clean work bench with the open ends of the caliper bores facing up.
  2. Dip the new piston seal in brake fluid GM P/N 12377967 (Canadian P/N 992667) or equivalent.

  3. Object Number: 171569  Size: SH
  4. Gently work the piston seal around the caliper bore with a finger until the seal seats in the piston seal groove.
  5. Ensure that the piston seal is not twisted or rolled in the groove.
  6. Lubricate the piston and the caliper bore with brake fluid GM P/N 12377967 (Canadian P/N 992667) or equivalent.
  7. Install the dust boot. The dust boot overlaps the stepped edge of the piston.
  8. Gently push the piston into the caliper bore.
  9. Rotate the piston slightly in order to prevent dislodging the piston seal.

  10. Object Number: 1533621  Size: SH
  11. Press the dust boot (1) into the counterbore in the brake caliper housing (4).
  12. Caution: Refer to Fastener Caution in the Preface section.

  13. Install the brake caliper bleeder valve.
  14. Tighten
    Tighten the brake caliper bleeder valve to 17 N·m (13 lb ft).