Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Audible Warnings Schematics Connector End View Reference: Instrument Panel, Gages, and Console Connector End Views or Entertainment Connector End Views DEFINITION: The chime sounds with the driver door open. | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 | Are any indicators illuminated? | -- | Go to Step 3 | |
3 |
Does the chime sound? | -- | Go to Step 4 | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems |
4 | Disconnect the instrument panel cluster (IPC). Does the chime sound? | -- | Go to Step 5 | Go to Step 6 |
5 | Is the vehicle equipped with a chime module (UL5)? | -- | Go to Step 11 | Go to Step 12 |
6 |
Does the test lamp illuminate? | -- | Go to Step 8 | Go to Step 7 |
7 |
Does the test lamp illuminate? | -- | Go to Step 9 | Go to Step 10 |
8 | Test the key in ignition switch signal circuit for a short to ground between the ignition key alarm switch and the IPC. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 14 |
9 | Test the key in ignition switch signal circuit for a short to ground between the driver door ajar switch and the ignition key alarm switch. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 15 |
10 | Test the driver door ajar switch signal circuit for a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 13 |
11 | Inspect for poor connections at the harness connector of the chime module. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 16 |
12 | Inspect for poor connections at the harness connector of the radio. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 17 |
13 | Inspect for poor connections at the harness connector of the driver door ajar switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 18 |
14 | Inspect for poor connections at the harness connector of the IPC. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 19 |
15 | Inspect for poor connections at the harness connector of the ignition key alarm switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 21 | Go to Step 20 |
16 | Replace the chime module. Refer to Multifunction Alarm Module Replacement . Did you complete the replacement? | -- | Go to Step 21 | -- |
17 | Replace the radio. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 21 | -- |
18 | Replace the driver door ajar switch. Refer to Front Side Door Lock Replacement in Doors. Did you complete the replacement? | -- | Go to Step 21 | -- |
19 | Replace the IPC. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 21 | -- |
20 | Replace the ignition key alarm switch. Refer to Ignition and Start Switch Replacement in Steering Wheel and Column. Did you find and correct the condition? | -- | Go to Step 21 | -- |
21 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 2 |
