Generator Bracket Replacement LG5
Removal Procedure
- Disconnect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
- Remove the drive belt. Refer to Caterpillar® 3126 Unit Repair Manual.
- Remove the air cleaner layer. Refer to
Air Cleaner Replacement
for the 7.1L (Caterpillar) engine.
- Remove the generator. Refer to
Generator Replacement
.
- Remove the generator bracket bolts.
- Remove the generator bracket.
Installation Procedure
- Install the generator bracket to the engine.
Notice: Refer to Fastener Notice in the Preface section.
- Install the generator bracket bolts.
Tighten
Tighten the generator bracket bolts to 50 N·m (37 lb ft).
- Install the generator. Refer to
Generator Replacement
.
- Install the air cleaner layer. Refer to
Air Cleaner Replacement
for the 7.1L (Caterpillar) engine.
- Install the drive belt. Refer to Caterpillar® 3126 Unit Repair Manual.
- Connect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
Generator Bracket Replacement L18
Removal Procedure
- Remove the air cleaner layer. Refer to
Air Cleaner Replacement
.
- Remove the drive belt tensioner. Refer to
Drive Belt Tensioner Replacement
.
- Remove the drive belt idler pulley, if equipped. Refer to
Drive Belt Idler Pulley Replacement
- Remove the generator. Refer to
Generator Replacement
.
- Remove the fan pulley bolts and pulley.
- Remove the generator bracket bolts and nut.
- Remove the generator bracket from the stud.
Installation Procedure
Notice: Refer to Fastener Notice in the Preface section.
- Slide the generator bracket onto the stud.
- Install the generator bracket bolts and nut.
Tighten
Tighten the generator bracket bolts and nut to 41 N·m (30 lb ft).
- Install the fan pulley and bolts.
Tighten
Tighten the fan pulley bolts to 45 N·m (33 lb ft).
- Install the generator. Refer to
Generator Replacement
.
- Install the drive belt idler pulley, if equipped. Refer to
Drive Belt Idler Pulley Replacement
.
- Install the drive belt tensioner. Refer to
Drive Belt Tensioner Replacement
.
- Install the air cleaner layer. Refer to
Air Cleaner Replacement
.
Generator Bracket Replacement 6.6L (LLY)
Removal Procedure
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing
any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to
the vehicle or its components.
- Disconnect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
- Remove the air cleaner. Refer to
Air Cleaner Replacement
.
- Remove the drive belt. Refer to
Drive Belt Replacement
.
- Remove the upper fan shroud. Refer to
Fan Shroud Replacement
.
- Remove the electrical harness clip bolts.
- Disconnect the generator electrical connector.
- Remove the positive battery cable from the generator, perform the following:
7.1. | Slide the boot down to access the terminal stud. |
7.2. | Remove the positive cable nut. |
7.3. | Remove the positive cable. |
- Remove the drive belt tensioner bolt.
- Remove the generator mounting bracket bolts.
- Remove the generator mounting bracket.
- If necessary, remove the idler pulleys.
Installation Procedure
Notice: Refer to Fastener Notice in the Preface section.
- If necessary, install the idler pulleys.
Tighten
Tighten the bolts to 50 N·m (37 lb ft).
- Install the generator mounting bracket.
- Install the generator mounting bracket bolts.
Tighten
Tighten the bolts to 50 N·m (37 lb ft).
- Install the drive belt tensioner bolt.
Tighten
Tighten the bolt to 50 N·m (37 lb ft).
- Install the positive battery cable to the generator, perform the following:
5.1. | Install the positive cable. |
5.2. | Install the positive cable nut. |
Tighten
Tighten the nut to 9 N·m (80 lb in).
5.3. | Slide the boot up to cover the terminal stud. |
- Connect the generator electrical connector.
- Install the electrical harness clip bolts.
Tighten
Tighten the bolts to 10 N·m (89 lb in).
- Install the upper fan shroud. Refer to
Fan Shroud Replacement
.
- Install the drive belt. Refer to
Drive Belt Replacement
.
- Install the air cleaner. Refer to
Air Cleaner Replacement
.
- Connect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.