Hood Emblem/Nameplate Replacement. GMC Truck TopKick C-Series (Conventional) C6/C7/C8 2009

For 1990-2009 cars only

Makes 🢒 GMC_Truck 🢒 2009 🢒 TopKick C-Series (Conventional) C6/C7/C8 🢒 Body Hardware and Trim 🢒 Exterior Trim 🢒 Hood Emblem/Nameplate Replacement

Hood Emblem/Nameplate Replacement Chevrolet, GMC, Isuzu

Callout	Component Name
1	Hood Nameplate When removing protective liners from adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion. Use a J 25070 or equivalent to remove the old nameplate. Clean all adhesive from the rear edge of the hood, wipe surface dry with a clean lint-free towel prior to installing the new nameplate. Apply the new nameplate with the hood in the closed position. Apply pressure to the nameplate to ensure full adhesion is made to the hood.

Callout

Component Name

Hood Nameplate

When removing protective liners from adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
Use a J 25070 or equivalent to remove the old nameplate. Clean all adhesive from the rear edge of the hood, wipe surface dry with a clean lint-free towel prior to installing the new nameplate.
Apply the new nameplate with the hood in the closed position.
Apply pressure to the nameplate to ensure full adhesion is made to the hood.

Hood Emblem/Nameplate Replacement Duramax

Special Tools

J 25070 Heat Gun

Removal Procedure

When replacing an emblem/nameplate, do the following:

•	Use tape to protect the mounting surface during removal.

•	Use tape for alignment marks for installation of the emblem/nameplate.

To remove an emblem/nameplate, heat the emblem/nameplate using a J 25070 .
Apply the heat using a circular motion for about 30 seconds holding the J 25070 approximately 152 mm (6 in) from the surface.

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Use a plastic, flat-bladed tool to remove the emblem/nameplate from the panel surface.
When replacing, remove all adhesive as follows:

•	For body panels, use a 3M™ Scotch Brite molding adhesive remover disk 3M™ P/N 07501 or equivalent.

•	For plastic panels use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a, 50/50 mixture, by volume of isopropyl alcohol and water in order to remove the adhesive.

Installation Procedure

Note: Apply the emblem/nameplate in an environment that is free from dust or other dirt that could come into contact with the sticky backing. Foreign material may cause improper adhesion.

Clean the area where the emblem/nameplate will be installed.

Use a lint free cloth and Varnish Makers and Painters (VMP) naphtha or a, 50/50 mixture, by volume of isopropyl alcohol and water in order to clean the area.

Dry the area thoroughly.
If the location of the emblem/nameplate has not been marked, apply tape and use the following dimensions:

For the emblem/nameplate, install to the following dimensions:

•	Center the emblem from top to bottom on the fender.

•	Dimension is 85 mm (3.34 in) from the back of emblem to the rear of the fender.

Heat the mounting surface to approximately 27-41°C (80-105°F) using the J 25070 , if necessary.
Ensure that the temperature of the emblem/nameplate is approximately 29-32°C (85-90°F).

Note: Do not touch the adhesive backing on the emblem/nameplate.

Remove the protective liner from the back of the emblem/nameplate.
Position the emblem/nameplate to the location marks and press the emblem/nameplate to the mounting surface.
Apply equal pressure along the emblem/nameplate in order to uniformly bond the item to the mounting surface.
Remove the protective tape from the mounting surface.