Power Brake Booster Inlet Hose Replacement LG4/LG5/LF6 and LF8

Note: Note the position of all the tie-wraps, power steering hoses and the hose insulators for proper re-installation.

1. Remove the tie-wraps and the hose insulators.



2. Disconnect the hydraulic brake booster inlet hose from the hydraulic brake booster.



3. Disconnect the hydraulic brake booster inlet hose from the of the power steering pump. Refer to Power Steering Hose Quick Connect Fitting Replacement.
4. Remove the hydraulic brake booster inlet hose from vehicle.

Caution: Do not start the engine with any power steering hose disconnected, or damage to the components could occur.

1. Connect the hydraulic brake booster inlet hose to the of the power steering pump. Refer to Power Steering Hose Quick Connect Fitting Replacement.



2. Install the hydraulic brake booster inlet hose to vehicle.

Caution: Refer to Fastener Caution in the Preface section.

3. Connect the hydraulic brake booster inlet hose to the hydraulic brake booster.

Tighten
Tighten the hydraulic brake booster inlet hose fittings to 27 N·m (20 lb ft).

4. Install the tie wraps and the hose insulators.
5. Bleed the system. Refer to Power Steering System Bleeding.

Power Brake Booster Inlet Hose Replacement LB7

Note: Note the position of all the tie-wraps, power steering hoses and the hose insulators for proper re-installation.

1. Remove the tie-wraps and the hose insulators.



2. Disconnect the hydraulic brake booster inlet hose from the of the power steering gear outlet. Refer to Power Steering Hose Quick Connect Fitting Replacement.
3. Remove the clips and isolators holding the power brake booster inlet hose to the frame and body.



4. Disconnect the hydraulic brake booster inlet hose from the hydraulic brake booster.
5. Remove the hydraulic brake booster inlet hose from vehicle.

Caution: Do not start the engine with any power steering hose disconnected, or damage to the components could occur.

1. Install the hydraulic brake booster inlet hose to vehicle.

Caution: Refer to Fastener Caution in the Preface section.

2. Install the hydraulic brake booster inlet hose to the hydraulic brake booster.

Tighten
Tighten the hydraulic brake booster inlet hose fittings to 27 N·m (20 lb ft).

3. Install the clips and isolators holding the power brake booster inlet hose to the frame and body.



4. Connect the hydraulic brake booster inlet hose to the power steering gear. Refer to Power Steering Hose Quick Connect Fitting Replacement.
5. Install the tie wraps and the hose insulators.
6. Bleed the system. Refer to Power Steering System Bleeding.

Power Brake Booster Inlet Hose Replacement L18, LLY and LMM

Note: Note the position of all the tie-wraps, power steering hoses and the hose insulators for proper re-installation.

1. Remove the tie-wraps and the hose insulators.



2. Disconnect the hydraulic brake booster inlet hose from the of the power steering pump. Refer to Power Steering Hose Quick Connect Fitting Replacement.



3. Disconnect the hydraulic brake booster inlet hose from the hydraulic brake booster.
4. Remove the hydraulic brake booster inlet hose from vehicle.

Caution: Do not start the engine with any power steering hose disconnected, or damage to the components could occur.

1. Install the hydraulic brake booster inlet hose to vehicle.

Caution: Refer to Fastener Caution in the Preface section.

2. Install the hydraulic brake booster inlet hose to the hydraulic brake booster.

Tighten
Tighten the hydraulic brake booster inlet hose fittings to 27 N·m (20 lb ft).




3. Connect the hydraulic brake booster inlet hose to the power steering pump. Refer to Power Steering Hose Quick Connect Fitting Replacement.
4. Install the tie wraps and the hose insulators.
5. Bleed the system. Refer to Power Steering System Bleeding.