Circuit Description
The evaporative system includes the following components:
| • | The fuel tank |
| • | The evaporative emission (EVAP) vent solenoid |
| • | The fuel tank pressure sensor |
| • | The fuel pipes and hoses |
| • | The vapor lines |
| • | The fuel cap |
| • | The evaporative emission canister |
| • | The purge lines |
| • | The EVAP purge solenoid |
The EVAP purge solenoid valve allows the manifold vacuum to purge the canister. The vehicle control module (VCM) supplies a ground in order to energize the solenoid valve (purge ON). The EVAP purge solenoid control by the VCM is pulse width modulated (PWM) or turned ON and OFF several times a second. The duty cycle (pulse width) is determined by the engine operating conditions including the load, the throttle position, the coolant temperature, and the ambient temperature. The duty cycle is calculated by the VCM, and the purge solenoid is commanded ON when certain conditions have been met.
The system checks for conditions that cause the EVAP system to purge continuously by commanding the EVAP vent solenoid ON and the EVAP purge solenoid OFF (EVAP vent solenoid CLOSED, EVAP purge PWM 0 percent). If the fuel tank vacuum level increases during the test, a continuous purge flow condition is indicated. The following items can cause this condition:
| • | A leaking EVAP purge solenoid |
| • | A grounded EVAP purge solenoid driver circuit |
If any of these conditions are present, a DTC P1441 sets.
Conditions for Running the DTC
| • | No active manifold absolute pressure (MAP) sensor DTCs |
| • | No active throttle position (TP) sensor DTCs |
| • | No active vehicle speed sensor (VSS) DTCs |
| • | No active oxygen (O2) sensor DTCs |
| • | No active engine coolant temperature (ECT) sensor DTCs |
| • | No active intake air temperature (IAT) sensor DTCs |
| • | DTC P0125 not active |
| • | The fuel level is between 12.5 percent-88 percent. |
| • | The system voltage is between 10 volts-17 volts. |
| • | The ECT is between 4-30°C (39°F-86°F). |
| • | The IAT is between 4-30°C (39°F-86°F). |
| • | The cold start temperature difference (ECT minus IAT) is less than : |
| - | 1.5°C (35°F) when the IAT is more than the ECT |
| - | 8°C (46°F) when the ECT is more than the IAT |
| • | The BARO is more than 72.5 kPa. |
Conditions for Setting the DTC
The EVAP system develops a vacuum more than a calibrated value when purge is not commanded.
Action Taken When the DTC Sets
The VCM will turn ON the malfunction indicator lamp (MIL) after 2 consecutive driving cycles with the fault active.
Conditions for Clearing the MIL or DTC
| • | The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed. |
| • | A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle. |
| • | Use a scan tool in order to clear the DTCs. |
Diagnostic Aids
Important: An accurate indication of fuel level is required for the VCM to properly Pass or Fail this DTC. Always diagnose fuel level sensor DTCs before performing this DTCs table. Always check for fuel level sensor DTCs stored in History.
Check for misrouted vacuum lines or fuel vapor lines. Misroutings may cause unintended purge of the canister.
Refer to Evaporative Emission System Cleaning before starting repairs.
Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.
Inspect the wiring harness to the EVAP purge solenoid and the fuel tank pressure sensor for an intermittent or short circuit.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step determines if the EVAP purge solenoid is leaking.
-
This step determines if the EVAP canister purge valve driver circuit is shorted to ground.
-
This step determines if the EVAP canister purge valve driver circuit wiring or the VCM are at fault.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | ||
Does the vacuum gauge indicate any vacuum while commanded OFF? | -- | Go to Diagnostic Aids | ||
Disconnect the electrical connector from the purge solenoid. Does the vacuum gauge still indicate vacuum? | -- | |||
4 |
Important:: Check for carbon contamination. Refer to Evaporative Emission System Cleaning . Replace the EVAP purge solenoid. Refer to Evaporative Emission Canister Purge Solenoid Valve Replacement . Is the action complete? | -- | -- | |
Is the test lamp Illuminated? | -- | |||
6 |
Important: The replacement VCM must be programmed. Replace the VCM. Refer to VCM Replacement/Programming . Is the action complete? | -- | -- | |
7 | Repair the short to ground in the EVAP canister purge valve driver circuit. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |
8 |
Does the scan tool indicate the diagnostic Passed? | -- | -- | |
9 | Does the scan tool display any additional undiagnosed DTCs? | -- | Go to the applicable DTC table | System OK |
