Front Seat Belt Replacement Regular Cab With Bucket Seat

Removal Procedure

Caution: To help avoid personal injury from unrepaired crash damage to a restraint system, perform the seat belt check for each seat belt system. Replace the seat belt system if there is any doubt about the condition of system components.

Notice: To prevent possible seat belt damage, refer to the following items before servicing or replacing lap and shoulder belts, including single loop belt systems:

-	Replace only the part in question.

-	Do not intermix standard and deluxe belts on front or rear seats.

-	All attachment hardware must be replaced, not reused.

•	Keep sharp edges and damaging objects away from belts.

•	Avoid bending or damaging any portion of the belt buckle or latch plate.

•	Do not bleach or dye belt or strap webbing. Clean with a mild soap solution and water.

•	When installing lap or shoulder belt anchor bolts, start the bolts by hand to ensure that the bolts are threaded straight.

•	Do not attempt repairs on lap or shoulder belt retractor mechanisms to lap belt retractor covers. Replace defective assemblies with new service replacement parts.

•	Do not attempt to remove the seat belt retractor cover. The cover and the long rivet securing the cover to the retractor are not available as service replacement parts.

1. Remove the cover from the door pillar anchor plate. Pry up the bottom.



2. Remove the bolt from the door pillar weld nut.



3. Remove the bolt retaining the retractor to the floor panel.
4. Remove the retractor from the vehicle.

Installation Procedure

1. Install the retractor and belt to the floor.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the bolt through the retractor into the floor panel weld nut.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).




3. Install the bolt through the anchor plate and washer into the door pillar weld nut.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).

4. Install the cover over the door pillar anchor plate.

Front Seat Belt Replacement Regular Cab With Bench Seat

Removal Procedure

Caution: To help avoid personal injury from unrepaired crash damage to a restraint system, perform the seat belt check for each seat belt system. Replace the seat belt system if there is any doubt about the condition of system components.

Notice: To prevent possible seat belt damage, refer to the following items before servicing or replacing lap and shoulder belts, including single loop belt systems:

-	Replace only the part in question.

-	Do not intermix standard and deluxe belts on front or rear seats.

-	All attachment hardware must be replaced, not reused.

•	Keep sharp edges and damaging objects away from belts.

•	Avoid bending or damaging any portion of the belt buckle or latch plate.

•	Do not bleach or dye belt or strap webbing. Clean with a mild soap solution and water.

•	When installing lap or shoulder belt anchor bolts, start the bolts by hand to ensure that the bolts are threaded straight.

•	Do not attempt repairs on lap or shoulder belt retractor mechanisms to lap belt retractor covers. Replace defective assemblies with new service replacement parts.

•	Do not attempt to remove the seat belt retractor cover. The cover and the long rivet securing the cover to the retractor are not available as service replacement parts.

1. Remove the cover from the door pillar anchor plate. Pry up the bottom.



2. Remove the bolt from the door pillar weld nut.



3. Remove the bolt retaining the retractor to the floor panel.
4. Remove the retractor from the vehicle.

Installation Procedure

1. Install the retractor and belt to the floor.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the bolt through the retractor into the floor panel weld nut.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).




3. Install the bolt through the anchor plate and washer into the door pillar weld nut.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).

4. Install the cover over the door pillar anchor plate.

Front Seat Belt Replacement Crew Cab

Removal Procedure

Caution: To help avoid personal injury from unrepaired crash damage to a restraint system, perform the seat belt check for each seat belt system. Replace the seat belt system if there is any doubt about the condition of system components.

Notice: To prevent possible seat belt damage, refer to the following items before servicing or replacing lap and shoulder belts, including single loop belt systems:

-	Replace only the part in question.

-	Do not intermix standard and deluxe belts on front or rear seats.

-	All attachment hardware must be replaced, not reused.

•	Keep sharp edges and damaging objects away from belts.

•	Avoid bending or damaging any portion of the belt buckle or latch plate.

•	Do not bleach or dye belt or strap webbing. Clean with a mild soap solution and water.

•	When installing lap or shoulder belt anchor bolts, start the bolts by hand to ensure that the bolts are threaded straight.

•	Do not attempt repairs on lap or shoulder belt retractor mechanisms to lap belt retractor covers. Replace defective assemblies with new service replacement parts.

•	Do not attempt to remove the seat belt retractor cover. The cover and the long rivet securing the cover to the retractor are not available as service replacement parts.

1. Remove the cover from the door pillar anchor plate. Pry up the bottom.



2. Remove the bolt from the door pillar weld nut.



3. Remove the bolt retaining the retractor to the floor panel.
4. Remove the retractor from the vehicle.

Installation Procedure

1. Install the retractor and belt to the floor.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the bolt through the retractor into the floor panel weld nut.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).




3. Install the bolt through the anchor plate and washer into the door pillar weld nut.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).

4. Install the cover over the door pillar anchor plate.

Front Seat Belt Replacement Luxury

Removal Procedure

Caution: To help avoid personal injury from unrepaired crash damage to a restraint system, perform the seat belt check for each seat belt system. Replace the seat belt system if there is any doubt about the condition of system components.

Notice: To prevent possible seat belt damage, refer to the following items before servicing or replacing lap and shoulder belts, including single loop belt systems:

-	Replace only the part in question.

-	Do not intermix standard and deluxe belts on front or rear seats.

-	All attachment hardware must be replaced, not reused.

•	Keep sharp edges and damaging objects away from belts.

•	Avoid bending or damaging any portion of the belt buckle or latch plate.

•	Do not bleach or dye belt or strap webbing. Clean with a mild soap solution and water.

•	When installing lap or shoulder belt anchor bolts, start the bolts by hand to ensure that the bolts are threaded straight.

•	Do not attempt repairs on lap or shoulder belt retractor mechanisms to lap belt retractor covers. Replace defective assemblies with new service replacement parts.

•	Do not attempt to remove the seat belt retractor cover. The cover and the long rivet securing the cover to the retractor are not available as service replacement parts.

1. Remove the cover from the door pillar anchor plate. Pry up the bottom.



2. Remove the bolt from the door pillar weld nut.



3. Remove the bolt retaining the retractor to the floor panel.
4. Remove the retractor from the vehicle.

Installation Procedure

1. Install the retractor and belt to the floor.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the bolt through the retractor into the floor panel weld nut.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).




3. Install the bolt through the anchor plate and washer into the door pillar weld nut.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).

4. Install the cover over the door pillar anchor plate.

Front Seat Belt Replacement Extended Cab With Bucket Seat

Removal Procedure

Caution: To help avoid personal injury from unrepaired crash damage to a restraint system, perform the seat belt check for each seat belt system. Replace the seat belt system if there is any doubt about the condition of system components.

Notice: To prevent possible seat belt damage, refer to the following items before servicing or replacing lap and shoulder belts, including single loop belt systems:

-	Replace only the part in question.

-	Do not intermix standard and deluxe belts on front or rear seats.

-	All attachment hardware must be replaced, not reused.

•	Keep sharp edges and damaging objects away from belts.

•	Avoid bending or damaging any portion of the belt buckle or latch plate.

•	Do not bleach or dye belt or strap webbing. Clean with a mild soap solution and water.

•	When installing lap or shoulder belt anchor bolts, start the bolts by hand to ensure that the bolts are threaded straight.

•	Do not attempt repairs on lap or shoulder belt retractor mechanisms to lap belt retractor covers. Replace defective assemblies with new service replacement parts.

•	Do not attempt to remove the seat belt retractor cover. The cover and the long rivet securing the cover to the retractor are not available as service replacement parts.

1. Remove the cover from the door pillar anchor plate. Pry up the bottom.



2. Remove the bolt from the door pillar weld nut.



3. Remove the bolt retaining the retractor to the floor panel.
4. Remove the retractor from the vehicle.

Installation Procedure

1. Install the retractor and belt to the floor.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the bolt through the retractor into the floor panel weld nut.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).




3. Install the bolt through the anchor plate and washer into the door pillar weld nut.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).

4. Install the cover over the door pillar anchor plate.

Front Seat Belt Replacement Extended Cab With Bench Seat

Removal Procedure

Caution: To help avoid personal injury from unrepaired crash damage to a restraint system, perform the seat belt check for each seat belt system. Replace the seat belt system if there is any doubt about the condition of system components.

Notice: To prevent possible seat belt damage, refer to the following items before servicing or replacing lap and shoulder belts, including single loop belt systems:

-	Replace only the part in question.

-	Do not intermix standard and deluxe belts on front or rear seats.

-	All attachment hardware must be replaced, not reused.

•	Keep sharp edges and damaging objects away from belts.

•	Avoid bending or damaging any portion of the belt buckle or latch plate.

•	Do not bleach or dye belt or strap webbing. Clean with a mild soap solution and water.

•	When installing lap or shoulder belt anchor bolts, start the bolts by hand to ensure that the bolts are threaded straight.

•	Do not attempt repairs on lap or shoulder belt retractor mechanisms to lap belt retractor covers. Replace defective assemblies with new service replacement parts.

•	Do not attempt to remove the seat belt retractor cover. The cover and the long rivet securing the cover to the retractor are not available as service replacement parts.

1. Remove the cover from the door pillar anchor plate. Pry up the bottom.



2. Remove the bolt from the door pillar weld nut.



3. Remove the bolt retaining the retractor to the floor panel.
4. Remove the retractor from the vehicle.

Installation Procedure

1. Install the retractor and belt to the floor.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the bolt through the retractor into the floor panel weld nut.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).




3. Install the bolt through the anchor plate and washer into the door pillar weld nut.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).

4. Install the cover over the door pillar anchor plate.

Front Seat Belt Replacement Extended Cab With 3rd Door

Removal Procedure

Caution: To help avoid personal injury from unrepaired crash damage to a restraint system, perform the seat belt check for each seat belt system. Replace the seat belt system if there is any doubt about the condition of system components.

Notice: To prevent possible seat belt damage, refer to the following items before servicing or replacing lap and shoulder belts, including single loop belt systems:

-	Replace only the part in question.

-	Do not intermix standard and deluxe belts on front or rear seats.

-	All attachment hardware must be replaced, not reused.

•	Keep sharp edges and damaging objects away from belts.

•	Avoid bending or damaging any portion of the belt buckle or latch plate.

•	Do not bleach or dye belt or strap webbing. Clean with a mild soap solution and water.

•	When installing lap or shoulder belt anchor bolts, start the bolts by hand to ensure that the bolts are threaded straight.

•	Do not attempt repairs on lap or shoulder belt retractor mechanisms to lap belt retractor covers. Replace defective assemblies with new service replacement parts.

•	Do not attempt to remove the seat belt retractor cover. The cover and the long rivet securing the cover to the retractor are not available as service replacement parts.

1. Remove the retractor cover from the rear seat access panel.



2. Remove the bolt from the retractor in the rear seat access panel.
3. Remove the retractor from the vehicle.

Installation Procedure

1. Install the retractor and belt to the rear seat access panel.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the bolt through the retractor into the rear seat access panel.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).




3. Install the bolt through the anchor plate and washer into the rear seat access panel.

Tighten
Tighten the bolt to 55 N·m (41 lb ft).

4. Install the cover onto the rear seat access panel.