GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 2000 🢒 Yukon Denali 🢒 Body and Accessories 🢒 Theft Deterrent 🢒 DTC B0688 Security System Indicator Circuit High

Object Number: 573262 Size: LF
Theft Deterrent System Components
Passlock ™
GAUGES Fuse
IGN A Fuse and Ignition Switch
Indicator Lamps (Diesel Only)
Theft Deterrent System Schematic Icons
G103 and G104
G103 and G104

Circuit Description

The security indicator is a hardwired lamp that receives power from the gauges fuse 4 through CKT 39.

Conditions for Setting the DTC
    • The ignition switch is ON.
    • The EVO/Passlock™ module is unable to provide a complete path to ground for the security indicator due to a wiring fault or a defective EVO/Passlock™ module.

Action Taken When the DTC Sets
    • The ignition switch is ON.
    • The security indicator is commanded ON.
    • The EVO/Passlock™ module connector terminal B2 voltage is greater than 2.9 volts.
    • The security indicator may be on when the ignition switch is OFF if CKT 749 is shorted to battery power.

Conditions for Clearing the DTC
    • The DTC will clear after an ignition cycle has occurred without the fault.
    • The EVO/Passlock™ module history codes will be cleared after 100 ignition cycles with no current codes active.
    • Using a scan tool.

Diagnostic Aids
    • Perform a visual inspection of the wiring and the connectors.
    • Inspect the Passlock™ sensor harness for an intermittent or a short to battery. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The numbers below refer to the numbers on the diagnostic table:

  1. This step isolates the problem between the harness and the EVO/Passlock™ module.

    2.

  2. This step isolates the problem between the instrument cluster and the harness

Step

Action

Value(s)

Yes

No

1

Did you perform the VTD Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Theft Deterrent

2

  1. Turn the ignition switch OFF.
  2. Disconnect the EVO/Passlock™ module connector.
  3. Remove the security indicator lamp. Refer to Instrument Cluster Bulb Replacement .
  4. Reconnect the cluster without the lamp.
  5. Turn the ignition switch ON.
  6. Use a J 39200 in order to measure the voltage from the EVO/Passlock™ module connector terminal B2 to ground.

Is the voltage within the specified range?

9-16 volts

Go to Step 3

Go to  5

3

  1. Disconnect the instrument cluster connector. Refer to Instrument Cluster Replacement .
  2. Ensure that the ignition switch is still ON.
  3. Use a J 39200 in order to measure the voltage from the EVO/Passlock™ module connector terminal B2 to ground.

Is the voltage within the specified range?

9-16 volts

Go to Step 4

Go to Step 6

4

Repair the short to battery in CKT 749.

Is the repair complete?

--

Go to Diagnostic System Check - Theft Deterrent

--

5

Replace the EVO/Passlock™ module. Refer to Theft Deterrent Module Replacement .

Is the repair complete?

--

Go to Step 7

--

6

Replace the instrument cluster. Refer to Instrument Cluster Replacement in Instrument Panel, Gauges and Console.

Is the repair complete?

--

Go to Diagnostic System Check - Theft Deterrent

--

7
  1. Reconnect all of the previously disconnected connectors and the components.
  2. Turn the ignition switch ON.
  3. Connect the scan tool.
  4. Clear the EVO/Passlock™ module DTCs.
  5. Perform one of the following Passlock™ reprogramming procedures:

Is the repair complete?

--

Go to Diagnostic System Check - Theft Deterrent

--