Seat Belt Retractor Replacement - No. 2 Rear 60/40 Split - 50/50 Split

Caution: To avoid personal injury to the occupants of the vehicle, observe the following precautions:

1. Remove the seat from the vehicle. Refer to Rear Number 2 Seat Replacement or Rear Number 2 50-50 Seat Replacement in Seats.
2. In order to release the seat back, manually rotate the center latch. Rotate the latch until the seat back releases the seat back.



3. Remove the latch cover (1) from the seat.



4. Remove the seat belt anchor bolt (1) from the cushion frame.
5. Remove the head rests. Refer to Head Restraint Replacement in Seats.
6. Remove the seat back cover and pad. Refer to Rear Seat Back Cushion Cover and Pad Replacement .
7. Remove the seat back frame. Refer to Rear Seat Back Cushion Frame Replacement in Seats.



8. Remove the seatbelt retractor bolt cover (1).
9. Remove the retractor mounting bolts (2).



10. Remove the handle mounting screws (1).
11. Partially remove the seat cushion cover by separating the cushion trim J-strips.



12. Remove the bolts attaching the buckle to the seat cushion frame.
13. Remove the buckle and the latch from the seat frame.

1. Install the buckle and the latch to the seat frame.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the buckle bolts.

Tighten
Tighten the bolts to 53 N·m (39 lb ft).

3. Connect the seat cushion cover by joining the cushion trim J-strips.



4. Install the handle mounting screws (1).

Tighten
Tighten the screws to 7 N·m (61 lb in).

5. Install the seat back frame. Refer to Rear Seat Back Cushion Frame Replacement in Seats.



6. Install the retractor mounting bolt (2).

Tighten
Tighten the bolt to 53 N·m (39 lb ft).

7. Install the seatbelt retractor bolt cover (1).
8. Install the seat back cover and pad. Refer to Rear Seat Back Cushion Cover and Pad Replacement .
9. Install the headrests. Refer to Head Restraint Replacement in Seats.



10. Install the seat belt anchor bolt (1) to the cushion frame.

Tighten
Tighten the bolt to 53 N·m (39 lb ft).




11. Install the latch cover (1) to the seat.

Tighten
Tighten the screw to 2 N·m (18 lb in).

12. In order to secure the seat back, manually rotate the center latch. Rotate the latch until the seat back clicks into position.
13. Install the seat to the vehicle. Refer to Rear Number 2 Seat Replacement or Rear Number 2 50-50 Seat Replacement in Seats.

Seat Belt Retractor Replacement - No. 2 Rear Bench

Caution: To avoid personal injury to the occupants of the vehicle, observe the following precautions:

1. Remove the seat back cover and pad. Refer to Rear Seat Back Cushion Cover and Pad Replacement in Seats.
2. Remove the seat belt retractor bolt (1) from the seat frame.
3. Remove the retractor.

Notice: Refer to Fastener Notice in the Preface section.




1. Install the retractor.
2. Install the seat belt retractor bolt (1) to the seat frame.

Tighten
Tighten the bolt to 53 N·m (39 lb ft).

3. Install the seat back cover and pad. Refer to Rear Seat Back Cushion Cover and Pad Replacement in Seats.