The powertrain control module (PCM) and the electronic brake control module (EBCM) communicate on the serial data line whenever the ignition is ON.
The PCM supplies 5 volts through an internal resistor, to the EBCM on the requested torque signal circuit. The EBCM toggles this voltage to ground to create the requested torque signal.
This diagnostic procedure supports the following DTC:
DTC C0298 Powertrain Control Malfunction
The ignition is ON.
• | The ignition is ON. |
• | The engine is running at a speed greater than 450 RPM for 5-20 seconds. |
The EBCM receives a serial data message stating that the PCM has lost the ability to reduce engine torque.
The PCM receives an invalid requested torque signal for 3 seconds.
• | The EBCM disables the traction control system (TCS). |
• | The traction off indicator turns ON. |
• | The PCM sends a serial data message to the EBCM stating that the PCM has lost the ability to reduce engine torque. |
• | The EBCM sets DTC C0298 or DTC C0240 as a current DTC for as long as the malfunction is present. |
The conditions for setting the DTC are no longer present and you use the scan tool Clear DTCs function.
• | The conditions for setting the DTC are no longer present and you use the scan tool Clear DTCs function. |
• | A history DTC clears automatically after 40 consecutive warm-up cycles without a PCM detected failure. |
A requested torque signal malfunction is only one possible cause for the PCM to lose the ability to perform traction control. DTC C0298 may set due to engine overheating, throttle actuator control failure, loss of ignition timing control by the PCM, etc. If DTC P1571 has not set, refer to Diagnostic System Check - Vehicle in order to identify other possible causes of DTC C0298.
Thoroughly inspect connections or circuitry that may cause an intermittent malfunction.
Refer to the following:
The numbers below refer to the step numbers on the diagnostic table.
This step tests for voltage supplied to the EBCM from the PCM.
This step tests for a shorted resistor in the PCM, or a short to voltage within the requested torque circuit, by verifying that a large voltage drop occurs when a test lamp is connected in parallel with the DMM.
Step | Action | Values | Yes | No |
---|---|---|---|---|
Schematic Reference: Antilock Brake System Schematics Connector End View Reference: Antilock Brake System Connector End Views and Powertrain Control Module Connector End Views for the 4.8L, 5.3L and 6.0L engine | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
2 | Is DTC P0856 set? | -- | Go to Step 3 | Go to Diagnostic Aids |
3 |
Does DTC P0856 reset? | -- | Go to Step 4 | Go to Diagnostic Aids |
Does the voltage measure greater than the specified value? | 4.75 V | Go to Step 5 | Go to Step 8 | |
Does the voltage measure less than the specified value? | 0.15 V | Go to Step 6 | Go to Step 9 | |
6 |
Does the Hz frequency of the requested torque signal measure within the specified range? | 121-134 Hz | Go to Step 7 | Go to Step 11 |
7 | Use the DMM in order to measure the duty cycle of the requested torque signal circuit. Does the duty cycle of the requested torque signal measure within the specified range? | 40-95% | Go to Step 12 | Go to Step 13 |
8 | Test the requested torque signal circuit for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 10 |
9 | Test the requested torque signal circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 14 | Go to Step 12 | |
10 | Inspect for poor connections at the harness connector of the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 12 |
11 | Inspect for poor connections at the harness connector of the EBCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | -- | Go to Step 14 | Go to Step 13 |
12 | Replace the powertrain control module (PCM). Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 14 | -- |
13 | Replace the EBCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 14 | -- |
14 |
Does DTC P0856 reset? | -- | Go to Step 4 | System OK |