| Table 1: | Liftgate Module Scan Tool Data Parameters |
| Table 2: | Liftgate Module Scan Tool Output Controls |
Parameter | System State | Expected Value | Definition |
|---|---|---|---|
Operating Conditions: Ignition ON | |||
Air Bags Deployed | -- | No | This displays Yes or No. Yes is displayed if the any of the air bags deployed during the last open or close history data. |
Battery Voltage Signal 2 | -- | Varies | This displays volts. This is the voltage input supplied to the liftgate module. |
Calibration | -- | Varies | This displays Yes or No. Yes is displayed if a calibration cycle occurred during the last open or close history data. |
Crank Signal Present | -- | Varies | The scan tool displays Yes or No. This was the last state of the crank signal in the open or close history data. |
Door Lock Status | -- | Varies | The scan tool displays Locked or Unlocked. This was the last state of the door locks in the open or close history data. |
Fault Active | -- | Varies | This displays Yes or No. Yes is displayed if a fault was active in the open or close history data. |
Hall Sensor Feed Status | -- | No Output | The scan tool displays No Output or Short to Ground. This is the state of the hall sensor feed circuit. |
Hall Sensor Feed Status (history data) | -- | Varies | The scan tool displays No Output or Short to Ground. This was the last state of the hall sensor feed circuit in the open or close history data. |
Interrupted | -- | Varies | This displays Yes or No. Yes is displayed if the liftgate system was interrupted during an open or close cycle. |
LGM Clutch Actuator Cmd. | -- | Inactive | This displays Active or Inactive. This is the commanded state of the liftgate module clutch actuator. |
LGM Disable Switch | -- | Inactive | This displays Active or Inactive. This is the state of the liftgate disable switch. |
LGM Disable Switch (history data) | -- | Inactive | This displays Active or Inactive. This was the last state of the liftgate disable switch during the last open or close history data. |
LGM Front Control Switch | -- | Inactive | This displays Active or Inactive. This is the state of the front control switch of the liftgate module. |
LGM Full Open Switch | -- | Inactive | This displays Active or Inactive. This is the state of the full open liftgate switch. |
LGM Latch Fault | -- | Varies | This displays Yes or No. Yes is displayed if there was a latch fault in the open or close history data. |
LGM Latch Motor Cinch Cmd. | -- | Inactive | This displays Active or Inactive. This is the commanded state of the latch motor cinch. |
LGM Latch Pawl Sw. | -- | Inactive | This displays Active or Inactive. This is the state of the latch pawl switch. |
LGM Latch Ratchet Sw. | -- | Inactive | This displays Active or Inactive. This is the state of the latch ratchet switch. |
LGM Latch Motor Release Cmd. | -- | Inactive | This displays Active or Inactive. This is the commanded state of the latch motor release. |
LGM Latch Sector Sw. | -- | Inactive | This displays Active or Inactive. This is the state of the latch sector switch. |
LGM Motor Closed Cmd. | -- | Inactive | This displays Active or Inactive. This is the commanded state of the liftgate motor closing. |
LGM Motor Open Cmd. | -- | Inactive | This displays Active or Inactive. This is the commanded state of the liftgate motor opening. |
LGM Open/Close Position Learned | -- | Yes | The scan tool displays Yes or No. This is the state of the liftgate module open/close position programming. |
LGM Position Out of Range | -- | Varies | The scan tool displays Yes or No. Yes is displayed if the liftgate position was out of range in the last open or close history data. |
Liftgate Ajar Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the liftgate ajar switch. |
Liftgate Handle Sw. Status | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the liftgate handle switch. |
Liftgate Handle Sw. Status (history data) | -- | Inactive | The scan tool displays Active or Inactive. This was the last state of the liftgate handle switch in the open or close history data. |
Liftglass Ajar Switch | -- | Varies | The scan tool displays Ajar or Closed. This was the last state of the liftglass ajar switch in the open or close history data. |
Module Over Current Detected | -- | Varies | The scan tool displays Yes or No. Yes is displayed if the liftgate module detected an over current condition in the last open or close history data. |
No Signal | -- | Varies | The scan tool displays Yes or No. Yes is displayed if the liftgate module detected a no signal condition in the last open or close history data. |
Object Detection Sensor Status | -- | Active | The scan tool displays Active or Inactive. This is the state of the object detection sensor. |
Object Detection Sensor Status (history data) | -- | Varies | The scan tool displays Active or Inactive. This was the last state of the object detection sensor in the open or close history data. |
Object Sensor Supply Voltage | -- | Varies | This displays volts. This is the voltage input supplied to the object sensor. |
Obstacle Detected in Liftgate | -- | Varies | This displays Yes or No. Yes is displayed if an obstacle was detected in the last open or close history data. |
System Operation Status | -- | Varies | This displays OK or Not OK. OK is displayed if the system operation was normal during the last open or close history data. |
System Voltage | -- | Varies | This displays OK or Out of Range. This was the state of the system voltage during the last open or close history data. |
Temperature Out of Range | -- | Varies | This displays Yes or No. Yes is displayed if the system temperature was out of range during the last open or close history data. |
Theft Armed | -- | Varies | This displays Yes or No. This was the status of the theft system during the last open or close history data. |
Vehicle In Park | -- | Varies | This displays Yes or No. Yes is displayed if the vehicle was in Park during the last open or close history data. |
Vehicle Speed Too Fast | -- | Varies | This displays Yes or No. Yes is displayed if the vehicle speed exceeded the maximum predetermined speed during the last open or close history data. |
Scan Tool Output Control | Description |
|---|---|
LGM Open/Close Test | This will command the liftgate to open and close. |
