Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B3875 00: Wiper High Speed Relay CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
WPR HI Relay B+ | 1, 2 | 1, 2 | -- | -- |
Windshield Wiper Switch Signal | B3922 00 | 1 | 1 | -- |
Windshield Wiper Switch High Signal | 4 | 2 | 2 | -- |
Windshield Wiper Motor Park Switch Signal | 3 | 3 | -- | -- |
WPR Relay Control | B3715 02 | 1 | 4 | -- |
WPR HI Relay Control | 4 | 2 | B3875 00 | -- |
Windshield Wiper Motor High Speed Control | 2 | 2 | 4 | -- |
Windshield Wiper Motor Low Speed Control | 1 | 1 | 4 | -- |
Windshield Wiper Switch Low Reference | -- | 1, 2 | 1, 2 | -- |
Windshield Wiper Motor Ground | -- | 1, 2, 3 | -- | -- |
WPR Relay Ground | -- | 1 | -- | -- |
1. Delay or Low Speed Wipers Inoperative 2. High Speed Wipers Inoperative 3. Wipers Do Not Park 4. Wipers Always ON | ||||
Circuit/System Description
The body control module (BCM) monitors the wiper high speed relay control circuit only when wiper high speed mode is active. When the wiper high speed mode is requested, the BCM responds by applying a ground through the wiper high speed relay control circuit to the coil side of the relay, energizing the WPR HI Relay.
Conditions for Running the DTC
This DTC can set only when the output is actively being requested by the BCM.
Conditions for Setting the DTC
This DTC sets if the BCM detects a short to voltage on the WIPER 2 relay control circuit.
Action Taken When the DTC Sets
The BCM will not activate the output.
Conditions for Clearing the DTC
| • | The current DTC will become history when the request for the output is removed or when the condition for setting the fault is corrected. |
| • | The history DTC will clear after 50 consecutive ignition cycles without a fault present. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Wiper/Washer System Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, wiper switch in the HIGH position. Verify the windshield wipers are cycling at the high speed.
Circuit/System Testing
- Ignition OFF, disconnect the X5 harness connector at the BCM.
- Install a 10A fused jumper wire between the WIPER 1 relay control circuit terminal 20 and B+.
- Ignition ON, verify that the high speed wipers are not on.
- Install a 10A fused jumper wire between the WIPER 2 relay control circuit terminal 21 and ground. Verify the high speed wipers are on.
- If all circuits test normal, replace the BCM.
| ⇒ | If the high speed wipers are on, test the WIPER 2 relay control circuit terminal 21 for a short to ground. If the circuit tests normal, replace the underhood fuse block. |
| ⇒ | If the low speed wipers are not on, test the relay control circuit for a short to voltage or an open/high resistance. If the circuit tests normal replace the underhood fuse block. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for BCM replacement, setup, and programming |
