The camshaft position (CMP) actuator solenoid is controlled by the engine control module (ECM). The ECM sends a 12-volt pulse width modulated (PWM) signal to the CMP actuator solenoid. The CMP actuator solenoid positions the CMP actuator spool valve to control the amount of pressurized engine oil, which enters into the CMP actuator assembly. A low reference wire circuit between the CMP actuator solenoid and the ECM completes the electrical circuit. The frequency of the PWM signal is fixed at 150 Hz. The ECM can only command the CMP actuator to advance the valve timing from the camshaft park position, or retard the valve timing back to the park position. The total range of valve timing command is 23 degrees as measured at the camshaft, or 46 degrees as measured at the crankshaft.

DTC P0011 is a Type B DTC.

This test procedure requires that the vehicle battery has passed a load test and is completely charged. Refer to Battery Inspection/Test .

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Camshaft Actuator System Description

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

1. Ignition OFF, open the hood to disable the Auto-Stop function. Refer to Hybrid Modes of Operation Description .
2. Ignition ON, verify the scan tool hood position parameter displays Open.

⇒	If the hood position does not display Open, refer to Diagnostic Trouble Code (DTC) List - Vehicle for DTC P254F.

3. Observe the engine oil level. The engine oil level should be within the operating range on the oil indicator stick.
4. Start the engine. Allow the engine to reach normal operating temperature.
5. Monitor the engine oil pressure parameter value with the scan tool. The engine oil pressure must be at or above the minimum hot oil pressure values. Refer to Engine Mechanical Specifications .
6. Using the output control function of the scan tool, command the CMP actuator solenoid to 25 degrees. The CMP Desired parameter value should match the CMP Angle parameter value.
7. Observe the CMP Variance value on the scan tool. The CMP Variance value will increment for several seconds until the CMP Angle value matches the Desired CMP value. The CMP Variance value should then return to 0 degrees.
8. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that are captured in the Freeze Fame/Failure Records Data List.

Important: You must perform the Circuit/System Verification first.

Important: Incorrect engine oil viscosity, aftermarket engine oil additives, or engine oil that is overdue for changing, can greatly affect the performance of the camshaft actuator.

1. Ignition OFF, open the hood to disable the Auto-Stop function. Refer to Hybrid Modes of Operation Description .
2. Ignition ON, verify the scan tool hood position parameter displays Open.

⇒	If the hood position does not display Open, refer to Diagnostic Trouble Code (DTC) List - Vehicle for DTC P254F.

3. Ignition OFF, disconnect X112.
4. Test for less than 3 ohms between the low reference circuit ECM side, terminal 1 and ground.

⇒	If greater than 3 ohms, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

5. Remove the water pump from the engine. Refer to Water Pump Removal .
6. Inspect and test the remaining wire harness from X112 to the CMP solenoid for an open/high resistance or a short to ground.

⇒	If the circuit tests normal, perform the Component Testing for the CMP actuator solenoid.

⇒	If the CMP solenoid and the circuit test normal, refer to Camshaft Position Actuator Magnet Cleaning and Inspection and Camshaft Position Actuator Solenoid Valve Inspection .

Static Test

Important: You must perform the Circuit/System Testing first.

Test for 5.9 and 7.7 ohms at 20°C (68°F) between the solenoid control terminal 2 and the low reference terminal 1 at the CMP actuator solenoid.

Dynamic Test

Important: Do not allow electrical current to flow through the CMP actuator solenoid for more than 1-2 seconds, or damage to the solenoid may occur.

Point the CMP actuator solenoid vertically towards a shop towel. Connect one end of a fused jumper wire to the CMP actuator solenoid control circuit terminal 2 and 12 volts. Connect a second jumper wire to the low reference circuit terminal 1 and momentarily connect to ground. The CMP actuator solenoid should immediately extend.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.