• | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
• | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
• | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
---|---|---|---|---|
Clutch PC Solenoid 4 Control | P2720 | P2721 | P2721 | P2719 |
Clutch PC Solenoid 4 High Side Driver 2 | P1833 | P1833 | P1834 | P2719 |
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
---|---|---|---|---|
Clutch PC 4 Sol. CKT Status | OK | Open/Short to Volts | Short to GND | Open/Short to Volts |
High Side Driver 2 CKT Status | OK | Open/Short to GND | Open/Short to GND | Short to Volts |
The clutch pressure control (PC) solenoid 4 is integral to the control solenoid (w/body and TCM) valve assembly and has no serviceable parts. The PC solenoid 4 is a normally high-pressure control solenoid which provides fluid pressure to the B-2-6 clutch regulator valve. The TCM controls the solenoid pressure by regulating the exhaust fluid. When the TCM commands the solenoid off, the exhausting fluid is stopped and the B-2-6 pressure is high. When commanded on, the clutch PC solenoid 4 regulates the amount of exhausting transmission fluid. Solenoid power is supplied by the TCM through a high side driver (HSD). The HSD protects the circuits and components that the TCM powers. Should the circuit overload the driver will shutdown. After the overload is removed the HSD reset.
• | The engine run time is greater than 5 seconds. |
• | The clutch PC solenoid 4 is commanded ON or OFF. |
The TCM detects an internal electrical performance malfunction of the clutch PC solenoid 4 control circuit and the actual 2-6 clutch pressure does not equal the commanded 2-6 clutch pressure for 300 milliseconds.
The TCM detects an internal low voltage electrical malfunction of the clutch PC solenoid 4 control circuit for 300 milliseconds.
The TCM detects an internal high voltage electrical malfunction of the clutch PC solenoid 4 control circuit for 300 milliseconds.
• | DTCs P2719, P2720, and P2721 are Type A DTCs. |
• | The TCM defaults the transmission to a limited shift pattern utilizing 2 forward gears and reverse based on the default detected. |
• | The TCM commands maximum line pressure. |
• | The TCM freezes transmission adaptive functions. |
DTCs P2719, P2720, and P2721 are Type A DTCs.
When attempting to set solenoid electrical DTCs, ensure the TCM is warmed up and the transmission is operated in second gear long enough to ensure a 3°C (5°F) increase in TCM substrate temperature. This will place the TCM under the optimal conditions to test solenoid electrical DTCs.
Automatic Transmission Controls Schematics
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Control Module References for scan tool information
Perform the following procedure to place the control solenoid (w/body and TCM) valve assembly under the optimal conditions to test solenoid electrical DTCs.
The scan tool data parameter Clutch PC 4 Sol. CKT Status normally displays OK.
⇒ | If the parameter displays Open/Short to Volts or Short to GND or if the DTC resets, perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection and if no concerns are found, replace the control solenoid (w/body and TCM) valve assembly. |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• | Replace the control solenoid (w/body and TCM) valve assembly. Refer to Control Module References for replacement, setup, and programming. |
• | Perform the Service Fast Learn Adapts if internal transmission repairs are performed. |