GM Service Manual Online
For 1990-2009 cars only

Radiator Grille Emblem/Nameplate Replacement GMC


Object Number: 1687659  Size: SF

Callout

Component Name

1

Grille Name Plate Assembly (GMC)

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Tip

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from grille and wipe the surface dry with a clean lint-free towel prior to installing the new name plate.
  3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
  4. Using the palm of the hand, wet out the name plate to the body side and ensure full adhesion of the name plate is made.

Radiator Grille Emblem/Nameplate Replacement Escalade


Object Number: 1767210  Size: SF

Callout

Component Name

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

 

1

Emblem Assembly (Crest)

Tip

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from grille and wipe the surface dry with a clean lint-free towel prior to installing the new name plate.
  3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
  4. Using the palm of the hand, wet out the emblem to the grille and ensure full adhesion of the emblem is made.

2

Emblem Assembly (Wreath)

Tip

  1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
  2. Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from grille and wipe the surface dry with a clean lint-free towel prior to installing the new emblem.
  3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
  4. Using the palm of the hand, wet out the emblem to the grille and ensure full adhesion of the emblem is made.

Radiator Grille Emblem/Nameplate Replacement Chevrolet Tahoe Two-mode Hybrid


Object Number: 1966801  Size: SF

Callout

Component Name

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Preliminary Procedure

Remove the radiator upper grille. Refer to Radiator Upper Grille Replacement .

1

Radiator Grille Emblem Assembly Nut (Qty: 2)

Notice: Refer to Fastener Notice in the Preface section.

Tighten
1.5 N·m (13 lb in)

2

Radiator Grille Emblem Assembly

Tip
Ensure the foam tape is on the emblem for installation.

Radiator Grille Emblem/Nameplate Replacement PLATINUM


Object Number: 2039436  Size: SF

Callout

Component Name

Preliminary Procedure

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Remove the front bumper fascia assembly. Refer to Front Bumper Fascia Replacement .

1

Radiator Grille Emblem Assembly Screw (Qty: 2)

Notice: Refer to Fastener Notice in the Preface section.

Tighten
Hand tighten the screws.

2

Radiator Grille Emblem Assembly