Tools Required
• | J 8092
Universal Driver Handle - ¾ in - 10 |
• | J 29369-2
Bushing and Bearing Remover (2-3 inch) |
• | J 36609
Axle Tube Bearing Installer |
Removal Procedure
- Raise the vehicle. Refer to
Lifting and Jacking the Vehicle
.
- Drain the differential carrier assembly. Refer to
Front Axle Lubricant Replacement
.
- Remove the right side seal and/or bearing by performing the following steps:
3.3. | Install the inner axle shaft housing into a vise. |
Clamp only on the mounting flange of the inner axle shaft housing.
3.4. | Install the
J 29369-1
, 8.25 inch axle, or the
J 29369-2
, 9.25 inch axle, behind the inner axle shaft seal or the inner axle
shaft bearing as necessary. |
3.6. | Remove the inner axle shaft seal and/or the inner axle shaft bearing using the
J 2619-01
. |
Important: Support the wheel drive shaft in order to not over flex the CV joint.
- If only replacing the left side seal, perform the following steps:
4.1. | Place an alignment mark between the inner axle shaft and the wheel drive shaft. |
4.3. | Disconnect the wheel drive shaft from the inner axle shaft. |
4.4. | Remove the inner axle shaft using a hammer and a brass drift. |
4.5. | Remove the inner axle shaft seal using a suitable seal remover tool. |
- If replacing both the left side seal and bearing, perform the following steps:
5.2. | Place the differential carrier assembly into a vise. |
Clamp only on the mounting flange of the differential carrier assembly case.
5.3. | Remove the inner axle shaft using a hammer and a brass drift. |
5.4. | Install the
J 29369-1
, 8.25 inch axle, or the
J 29369-2
, 9.25 inch axle (1), behind the inner axle shaft seal or the
inner axle shaft bearing as necessary. |
5.6. | Remove the inner axle shaft seal and/or the inner axle shaft bearing using the
J 2619-01
. |
Installation Procedure
- Install the right side bearing with the square shoulder in using the
J 36609
(1) and the
J 8092
(2).
- Install the new axle shaft seal using the
J 45225
(1) and the
J 8092
(2).
- Install the inner axle shaft into the inner axle shaft housing.
Carefully tap the inner axle shaft into place with a soft-faced mallet.
- Install the inner axle shaft and clutch fork assembly components into the inner shaft housing. Refer to
Front Drive Axle Inner Shaft and Inner Shaft Housing Replacement
.
- Install the inner axle shaft and housing assembly to the differential carrier case assembly. Refer to
Front Drive Axle Inner Shaft and Inner Shaft Housing Replacement
.
- If both the left side bearing and seal was removed, perform the following step.
Install the left side bearing with the square shoulder in using the
J 36609
(1) and the
J 8092
(2).
- If both the left side bearing and seal was removed, perform the following step.
Install the new axle shaft seal using the
J 45225
(1) and the
J 8092
(2).
- If both the left side bearing and seal was removed, perform the following step. Install the inner axle shaft into the differential case side gear using a soft-faced mallet until the retaining ring on the inner axle shaft is fully seated within the
groove in the differential case side gear.
Pull back on the inner axle shaft to ensure that the inner axle shaft is properly retained in the differential case side gear.
- If both the left side bearing and seal was removed, perform the following step. Install the front differential carrier assembly. Refer to
Differential Carrier Assembly Replacement
.
- If only the left side seal was removed, perform the following step. Install the
seal using the
J 45225
and a soft-faced mallet.
Tap only on the center portion of the
J 45225
in order to drive the seal in evenly.
- If only the left side seal was removed, perform the following step. Install the inner axle shaft into the
differential case side gear using a soft-faced mallet until the retaining ring on the inner axle shaft is fully seated within the groove in the differential case side gear.
Pull back on the inner axle shaft to ensure that the inner axle shaft is
properly retained in the differential case side gear.
- If servicing the 8.25 inch axle, install the shock module. Refer to
Shock Absorber and Spring Assembly Replacement
.
- If only the left side seal was removed, perform the following step. Install the wheel drive shaft to the inner axle shaft.
Notice: Refer to Fastener Notice in the Preface section.
- If only the left side seal was removed, perform the following step. Install the wheel drive shaft to the inner axle shaft bolts.
Tighten
Tighten the wheel drive shaft to inner axle shaft bolts to 79 N·m (58 lb ft).
- Fill the differential carrier assembly. Use the correct fluid. Refer to
Front Axle Lubricant Replacement
.
- Lower the vehicle.