GM Service Manual Online
For 1990-2009 cars only

Tools Required

    • J 8001 Dial Indicator Set
    • J 36660-A Torque Angle Meter

    Object Number: 471041  Size: SH

    Important: 

       • Lubricate the crankshaft bearings and crankshaft with clean engine oil.
       • If undersized bearings are used, ensure that the bearings are fitted to the proper journals.

  1. Install the crankshaft upper bearings into the block. Apply clean engine oil to the bearing surfaces.

  2. Object Number: 471044  Size: SH
  3. Install the crankshaft lower bearings into the crankshaft bearing caps. Apply clean engine oil to the bearing surfaces.

  4. Object Number: 471047  Size: SH

    Notice: In order to prevent damage to the crankshaft position (CKP) sensor reluctor wheel/ring, care must be used when removing or installing this component.

  5. Install the crankshaft.

  6. Object Number: 647705  Size: SH

    Important: The bearing caps must be seated within 60 minutes of the sealer being applied. The bearing cap fasteners must be tightened within 5 minutes of the bearing caps being installed onto the engine block.

  7. Apply a (a) 13 mm (0.5 in) light film of sealant GM P/N 1052942 (Canadian P/N 10953466) or equivalent to the rear bearing cap sealing surface or to the rear bearing cap channel of the engine block. Apply the sealant to the bearing cap mating surface and bearing cap channel from the rear seal bore to the oil pan surface.

  8. Object Number: 679831  Size: SH

    Notice: In order to prevent the possibility of cylinder block or crankshaft bearing cap damage, the crankshaft bearing caps are tapped into the cylinder block cavity using a brass, lead, or a leather mallet before the attaching bolts are installed. Do not use attaching bolts to pull the crankshaft bearing caps into the seats. Failure to use this process may damage a cylinder block or a bearing cap.

    Notice: The crankshaft position (CKP) sensor reluctor wheel/ring is not serviced separately. Do not repair the CKP sensor reluctor wheel/ring. If the CKP sensor reluctor ring is damaged, the crankshaft assembly must be replaced.

    Important: Ensure that the triangle symbols on the crankshaft bearing caps are facing the front of the engine.

  9. Install the crankshaft bearing caps in the location the caps were marked and originally removed from.

  10. Object Number: 471055  Size: SH

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    Important: Tighten the crankshaft bearing cap inner bolts before tightening the crankshaft bearing cap outer studs.

  11. Install the bearing cap bolts and studs.
  12. Tighten

    1. Tighten the bearing cap 1-4 inner bolts a first pass to 30 N·m (22 lb ft).
    2. Tighten the bearing cap 1-4 outer studs a first pass to 30 N·m (22 lb ft).
    3. Tighten the bearing cap 1-4 inner bolts a final pass an additional 90 degrees using the J 36660-A .
    4. Tighten the bearing cap 1-4 outer studs a final pass an additional 80 degrees using the J 36660-A .
    5. Tighten the bearing cap 5 bolts and studs to 30 N·m (22 lb ft).
    6. Loosen the bearing cap 5 bolts and studs.
    7. Tighten the bearing cap 5 bolts and studs to 5 N·m (44 lb in).
  13. Thrust the crankshaft firmly rearward.
  14. Thrust the crankshaft firmly forward.
  15. Tighten

    1. Tighten the bearing cap 5 inner bolts a first pass to 30 N·m (22 lb ft).
    2. Tighten the bearing cap 5 outer studs a first pass to 30 N·m (22 lb ft).
    3. Tighten the bearing cap 5 inner bolts a final pass an additional 90 degrees using the J 36660-A .
    4. Tighten the bearing cap 5 outer studs a final pass an additional 80 degrees using the J 36660-A .

    Object Number: 677804  Size: SH
  16. Measure the crankshaft end play as follows:
  17. 9.1. Install the J 8001 or equivalent to the cylinder block, with the dial indicator plunger against one of the counterweights of the crankshaft.
    9.2. Firmly thrust the end of the crankshaft first rearward then forward. This will line up the rear crankshaft bearing and the crankshaft thrust surfaces.
    9.3. With the crankshaft pushed forward, zero the dial indicator. Move the crankshaft rearward, and read the end play measurement on the dial indicator. An optional method is to insert a feeler gage between the crankshaft and the bearing surface and measure the clearance. Refer to Engine Mechanical Specifications .
    9.4. If the correct end play cannot be obtained, inspect for the following conditions:
       • Verify that the correct size crankshaft bearing has been installed. Refer to Engine Mechanical Specifications .
       • Inspect the crankshaft thrust wall surface or surfaces for wear and/or excessive runout. Refer to Engine Mechanical Specifications .
    9.5. Inspect the crankshaft for binding. Turn the crankshaft to check for binding. If the crankshaft does not turn freely, loosen the crankshaft bearing bolts and studs, one cap at a time, until the tight bearing is located. The following condition or conditions could cause a lack of clearance at the bearing:
       • Burrs on the crankshaft bearing cap
       • Foreign material between the bearing and the block
       • Foreign material between the bearing and the bearing cap
       • A faulty crankshaft bearing
       • Improper size bearing

    Object Number: 470801  Size: SH

    Important: 

       • Ensure that the crankshaft position sensor is fully seated against the crankshaft reluctor ring. The upper flange on the sensor MAY NOT seat against the engine block.
       • The crankshaft position sensor bolt has a thread sealant applied to the threads. The thread sealant may have come off during the removal of the bolt. Ensure that the bolt hole is clean of any debris before installing the crankshaft sensor bolt.

  18. Inspect both crankshaft position sensor O-rings for cuts, cracks, tears or damage. Replace the O-rings as needed. Lubricate the crankshaft position sensor O-rings with clean engine oil.
  19. Install the crankshaft position sensor into the block.
  20. There may be a slight resistance as the O-rings seat into the engine block.

  21. Apply thread adhesive GM P/N 12345493 (Canadian P/N 10953488) or equivalent to the crankshaft position sensor bolt.
  22. Install the crankshaft position sensor bolt.
  23. Tighten
    Tighten the crankshaft position sensor bolt to 12 N·m (106 lb in).