Electronic Suspension Front Position Sensor Replacement 15 Series
Removal Procedure
- Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
in General Information.
- Disconnect the sensor
harness connector from the vehicle harness connector.
- Remove the wheel speed sensor wire from the real time damping
(RTD) sensor bracket.
- Remove the wheel speed sensor wire from the (RTD) sensor bracket.
- Remove the (RTD) sensor link bracket bolt from the upper control
arm.
- Remove the bolt from the
frame.
- Remove the position sensor from the vehicle.
Installation Procedure
- Install the position sensor
on the vehicle.
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the bolt to the frame.
Tighten
Tighten the bolts to 12 N·m (106 lb in).
- Install the (RTD) sensor
link bracket bolt to the upper control arm.
Tighten
Tighten the bolt to 9 N·m (80 lb in).
- Install the wheel speed sensor wire from the real time damping
(RTD) sensor bracket.
- Install the wheel speed sensor wire to the (RTD) sensor bracket.
- Connect the sensor harness connector to the vehicle harness connector.
- Remove the safety stands.
- Lower the vehicle.
Electronic Suspension Front Position Sensor Replacement 25 Series 2WD
Removal Procedure
- Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
in General Information.
- Disconnect the sensor
harness connector from the vehicle harness connector.
- Remove the wheel speed sensor wire from the RTD sensor bracket.
- Remove the RTD sensor link bracket bolt from the upper control
arm.
- Remove the bolt from the frame.
- Remove the position sensor from the vehicle.
Installation Procedure
- Install the position sensor
to the vehicle.
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the bolt to the frame.
Tighten
Tighten the bolts to 12 N·m (106 lb in).
- Install the RTD sensor link bracket bolt to the upper control
arm.
Tighten
Tighten the bolt to 9 N·m (80 lb in).
- Connect the sensor harness connector to the vehicle harness connector.
- Install the wheel speed sensor wire to the RTD sensor bracket.
- Install the RTD sensor link bracket bolt to the upper control
arm.
- Lower the vehicle.
Electronic Suspension Front Position Sensor Replacement 25 Series 4WD
Removal Procedure
- Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
in General Information.
- Disconnect the sensor
harness connector from the vehicle harness connector.
- Remove the wheel speed sensor wire from the real time damping
(RTD) sensor bracket.
- Remove the RTD sensor link bracket bolt from the upper
control arm.
- Remove the bolt from the frame.
- Remove the position sensor from the vehicle.
Installation Procedure
- Install the position sensor
on the vehicle.
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the bolt to the frame.
Tighten
Tighten the bolts to 12 N·m (106 lb in).
- Install the (RTD) sensor link bracket bolt to the upper control
arm.
Tighten
Tighten the bolt to 9 N·m (80 lb in).
- Install the wheel speed sensor wire to the real time damping (RTD)
sensor bracket.
- Connect the sensor harness connector to the vehicle harness connector.
- Lower the vehicle.