Refer to Engine Controls Schematics
Control Module, Cruise Control Switch, APP Sensor
.
Circuit Description
The accelerator pedal position (APP) sensor is mounted on the accelerator pedal assembly. The sensor is actually 3 individual APP sensors within one housing. Three separate signal, ground, and 5.0 volt reference circuits connect the APP sensor assembly and the throttle actuator control (TAC) module. Each sensor has a unique functionality. The APP sensor 1 signal increases as the accelerator pedal is depressed, from below 1.0 volt at 0 percent pedal travel, the pedal is at rest, to above 2.0 volts at 100 percent pedal travel, the pedal is fully depressed. The APP sensor 2 signal decreases from above 4.0 volts at 0 percent pedal travel to below 2.9 volts at 100 percent pedal travel. The APP sensor 3 signal decreases from above 3.8 volts at 0 percent pedal travel to below 3.1 volts at 100 percent pedal travel. Observe that the signal circuits or APP sensor 2 and APP sensor 3 pull up to 5 volts and the APP sensor 1 signal circuit pull to ground within the TAC module.
Conditions for Running the DTC
| • | DTCs P0606, P1517, P1518 are not set. |
| • | The ignition switch is in the crank or run position. |
| • | The ignition voltage is more than 5.23 volts. |
Conditions for Setting the DTC
| • | APP sensor 1 disagrees with APP sensor 2 by more than 10.5 percent and APP sensor 1 disagrees with APP sensor 3 by more than 13.0 percent. |
| • | All of the above conditions are met for less than 1 second. |
Action Taken When the DTC Sets
| • | The PCM stores the DTC information into memory when the diagnostic runs and fails. |
| • | The malfunction indicator lamp (MIL) will not illuminate. |
| • | The PCM records the operating conditions at the time the diagnostic fails. The PCM stores this information in the Freeze Frame and/or Failure Records. |
| • | If no other TAC System DTCs are set, the TAC System operates normally. If certain TAC System DTCs are set at the same time, the TAC system commands the engine to operate in a reduced engine power mode. The TAC system may command the engine to shut down. |
Conditions for Clearing the DTC
| • | A last test failed, or current DTC, clears when the diagnostic runs and does not fail. |
| • | A history DTC will clear after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic. |
| • | Use a scan tool in order to clear the DTC. |
Diagnostic Aids
Important:
• Remove any debris from the powertrain control module (PCM) or
TAC module connector surfaces before servicing the PCM or TAC module. Inspect
the PCM or TAC module connector gaskets when diagnosing or replacing
the modules. Ensure that the gaskets are installed correctly. The
gaskets prevent contaminate intrusion into the PCM or TAC modules. • For any test that requires probing the PCM or a component
harness connector, use the J 35616
connector test adapter kit to test the harness or component
terminals. Refer to
Using Connector Test Adapters
in Wiring Systems.
| • | The following may cause an intermittent: |
| - | Poor connections--Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
| - | Corrosion |
| - | Misrouted harness |
| - | Rubbed through the wire insulation |
| - | Broken wire inside the insulation |
| • | Inspect the TAC module connectors for signs of water intrusion. |
| • | When the TAC module detects a condition within the TAC system, more than one TAC system related DTC may set. This is due to the many redundant tests run continuously on this system. Locating and repairing one individual condition may correct more than one DTC. Keep this in mind when reviewing captured DTC info. |
| • | For an intermittent condition, refer to Symptoms . |
Test description
The numbers below refer to the steps numbers on the diagnostic table
-
This step determines if a communication condition exists.
-
This step isolates an internal APP sensor failure. The condition may only occur at a certain accelerator pedal position. Monitoring the APP angles for sensor 2 and sensor 3 is an accurate way of verifying the actual position of the pedal. The APP angles for all 3 sensors should be within a few percent of each other. When the pedal is at rest, the APP angle for all 3 sensors should be 0 percent. When the pedal is fully depressed all APP angles should be 100 percent.
-
The APP sensor 1 shares a common 5.0 volt reference circuit with the TP sensor 1. Monitoring the TP sensor 1 voltage aids in diagnosing the APP sensor 5.0 volt reference and ground circuits. If the scan tool displays near 0 volts then the circuits are OK.
-
This step determines whether the TAC module or a shorted circuit is causing the condition.
-
Excessive resistance in the circuit causes this DTC to set.
-
Excessive resistance in the circuit causes this DTC to set.
-
Excessive resistance in the circuit causes this DTC to set.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | ||
Is DTC P1518 also set? | -- | Go to DTC P1518 Throttle Actuator Control (TAC) Module Serial Data Circuit | ||
3 |
Important: Do not depress the accelerator pedal. Did any other TAC module or APP sensor DTCs set except P1125? | -- | Go to the applicable DTC table | |
4 | Monitor the APP sensor disagree parameter using the scan tool. Does the scan tool display YES for any of the disagree parameters? | -- | ||
Does the APP sensor 1 angle correspond to the APP sensors 2 and 3 angles? | -- | Go to Diagnostic Aids | ||
Does the scan tool display near the specified value? | 0 V | |||
7 |
Does the scan tool display near the specified value? | 0 V | ||
8 |
Does the scan tool display the specified value? | 5.0 V | ||
9 |
Does the DMM display continuity within the specified range? | 0-5 ohms | ||
Does the DMM indicate continuity to any other circuit? | -- | |||
Does the DMM display continuity within the specified range? | 0-5 ohms | |||
Does the DMM display continuity within the specified range? | 0-5 ohms | |||
Does the DMM display continuity within the specified range? | 0-5 ohms | |||
14 |
Did you find and correct the condition? | -- | ||
15 |
Did you find and correct the condition? | -- | ||
16 | Repair the open or excessive resistance in the affected circuit. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |
17 | Repair the shorted circuits that displayed continuity. Refer to Wiring Repairs in Wiring Systems. Is the action complete? | -- | -- | |
18 | Replace the accelerator pedal assembly. Refer to Accelerator Pedal Position Sensor Replacement . Is the action complete? | -- | -- | |
19 | Replace the TAC module. Refer to Electronic Throttle Actuator Control Module Replacement . Is the action complete? | -- | -- | |
20 |
Does the scan tool indicate that this diagnostic ran and passed? | -- | ||
21 | Select the Capture Info option and the review Info option using the scan tool. Does the scan tool display any DTCs that you have not diagnosed? | -- | Go to the applicable DTC table | System OK |
