DTC P1875 4WD Low Switch Circuit Electrical 4.3L
Circuit Description
For vehicles equipped with an active transfer case, the four wheel drive (4WD) low circuit consists of the vehicle control module (VCM), a transfer case control module and the circuit wiring. The transfer case control module controls the 4WD low signal on circuit 1694. When the operator selects 4WD low, the transfer case control module grounds circuit 1694, and the 4WD low signal voltage on the circuit changes from ignition voltage to zero volts. The VCM then compensates for transfer case gear reduction in the transmission output shaft speed (OSS) sensor signal. The VCM uses the transmission OSS sensor signal to adjust shift points, line pressure and torque converter clutch (TCC) scheduling.
For vehicles not equipped with an active transfer case, the 4WD low circuit consists of the VCM, a transfer case switch and the circuit wiring. The transfer case switch controls the 4WD low signal on circuit 1694. When the operator selects 4WD low, the transfer case switch closes and the 4WD low signal voltage on circuit 1694 changes from ignition voltage to zero volts. The VCM then compensates for transfer case gear reduction in the transmission output shaft speed (OSS) sensor signal. The VCM uses the transmission OSS sensor signal to adjust shift points, line pressure and TCC scheduling.
When the VCM detects a continuous open, short to ground or short to power in the 4WD low circuit, then DTC P1875 sets. DTC P1875 is a type B DTC.
Conditions for Running the DTC
| • | No TP sensor DTCs P0122, or P0123 |
| • | No VSS assembly DTCs P0502 or P0503 |
| • | No TCC solenoid valve DTC P0740 |
| • | No TCC stuck ON DTC P0742 |
| • | No 1-2 SS valve DTC P0751 or P0753 |
| • | No 2-3 SS valve DTC P0756 or P0758 |
| • | No TFP manual valve position switch DTC P1810 |
| • | No TCC PWM solenoid valve DTC P1860 |
| • | No transmission component slipping DTC P1870 |
| • | The engine speed is greater than 450 RPM for 5 seconds |
| • | The engine is not in fuel cutoff |
| • | The vehicle speed is greater than 11 km/h (7 mph) |
| • | The TP angle is 17-50% |
| • | The engine torque is between 50-400 ft. lbs |
| • | The engine vacuum is between 0-105 kPa |
| • | The gear range is D4 |
| • | The shift solenoid performance counters are zero |
| • | The TFT is 20-130°C (68-266°F) |
Conditions for Setting the DTC
DTC P1875 sets if one of the following conditions occurs:
Condition 1
| • | The 4WD low switch is in 4WD low. |
| • | The transfer case is not in 4WD low. |
| • | The TCC slip speed is -3000 to -50 RPM. |
| • | The transfer case ratio is 0.8-1.2 (the transfer case ratio is the engine speed divided by the transfer case output speed). |
| • | All conditions met for 5 seconds. |
Condition 2
| • | The 4WD low switch is not in 4WD low. |
| • | The transfer case is in 4WD low. |
| • | The TCC is commanded ON. |
| • | The TCC slip speed is 100 to 3000 RPM. |
| • | The transfer case ratio is 2.5-2.9. |
| • | All conditions met for 10 seconds. |
Action Taken When the DTC Sets
| • | The VCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. |
| • | The VCM commands a normal shift pattern (not a 4WD low shift pattern). |
| • | The VCM records the operating conditions when the Conditions for Setting the DTC are met. The VCM stores this information as Freeze Frame and Failure Records. |
| • | The VCM stores DTC P1875 in VCM history during the second consecutive trip in which the Conditions for Setting the DTC are met. |
Conditions for Clearing the MIL/DTC
| • | The VCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes. |
| • | A scan tool can clear the MIL/DTC. |
| • | The VCM clears the DTC from VCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring. |
| • | The VCM cancels the DTC default actions when the fault no longer exists and/or the ignition switch is OFF long enough in order to power down the VCM. |
Diagnostic Aids
| • | Inspect the connectors at the VCM, the transfer case control module (active transfer case vehicles), the transfer case switch connector (non-active transfer case vehicles) and all other circuit connecting points for an intermittent condition. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
| • | Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Wiring Systems. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for a short to ground in the 4WD low signal circuit (CKT 1694).
-
This step tests for an open in the 4WD low signal circuit (CKT 1694) or a faulty transfer case control module (active transfer case vehicles), or transfer case switch (non-active transfer case vehicles).
Step | Action | Value(s) | Yes | No | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Powertrain Diagnostic System Check? | -- | Go to Powertrain On Board Diagnostic (OBD) System Check (4.3L) in Engine Controls | |||||||||||||
2 |
Important: Before clearing the DTC, use the Scan Tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the VCM. Important: It may be necessary to drive the vehicle slightly forward to engage 4LO on the transfer case. Does the Scan Tool 4WD Low display Disabled when you select 4HI, then Enabled when you select 4LO? | -- | Go to Diagnostic Aids | |||||||||||||
Does the Scan Tool 4WD Low indicate Enabled? | -- | |||||||||||||||
Does the Scan Tool 4WD Low indicate Enabled when the 4WD low signal circuit (CKT 1694) is grounded? | -- | |||||||||||||||
5 | Replace the transfer case control module (active transfer case vehicles), or the transfer case selector switch (non-active transfer case vehicles). Refer to Transfer Case Shift Control Module Replacement (Automatic 4WD) (Transfer Case - NVG 246-NP8 Two Speed Automatic), or Transfer Case Switch Replacement (Transfer Case - NVG 261-NP2 Two Speed Manual) in Transfer Case (Two Speed Automatic). Did you complete the replacement? | -- | -- | |||||||||||||
6 | Test the 4WD low signal circuit (CKT 1694) for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||||||||||||||
7 | Test the 4WD low signal circuit (CKT 1694) for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||||||||||||||
8 | Replace the VCM. Refer to VCM Replacement/Programming in Engine Controls. Did you complete the replacement? | -- | -- | |||||||||||||
9 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | System OK |
DTC P1875 4WD Low Switch Circuit Electrical 4.8L and 5.3L
Circuit Description
For vehicles equipped with an active transfer case, the four wheel drive (4WD) low circuit consists of the powertrain control module (PCM), a transfer case control module and the circuit wiring. The transfer case control module controls the 4WD low signal on circuit 1694. When the operator selects 4WD low, the transfer case control module grounds circuit 1694, and the 4WD low signal voltage on the circuit changes from ignition voltage to zero volts. The PCM then compensates for transfer case gear reduction in the transmission output shaft speed (OSS) sensor signal. The PCM uses the transmission OSS sensor signal to adjust shift points, line pressure and torque converter clutch (TCC) scheduling.
For vehicles not equipped with an active transfer case, the 4WD low circuit consists of the PCM, a transfer case switch and the circuit wiring. The transfer case switch controls the 4WD low signal on circuit 1694. When the operator selects 4WD low, the transfer case switch closes and the 4WD low signal voltage on circuit 1694 changes from ignition voltage to zero volts. The PCM then compensates for transfer case gear reduction in the transmission output shaft speed (OSS) sensor signal. The PCM uses the transmission OSS sensor signal to adjust shift points, line pressure and TCC scheduling.
When the PCM detects a continuous open, short to ground or short to power in the 4WD low circuit, then DTC P1875 sets. DTC P1875 is a type B DTC.
Conditions for Running the DTC
| • | No TP sensor DTCs P0122, or P0123 |
| • | No VSS assembly DTCs P0502 or P0503 |
| • | No TCC solenoid valve DTC P0740 |
| • | No TCC stuck ON DTC P0742 |
| • | No 1-2 SS valve DTCs P0751 or P0753 |
| • | No 2-3 SS valve DTCs P0756 or P0758 |
| • | No TFP manual valve position switch DTC P1810 |
| • | No TCC PWM solenoid valve DTC P1860 |
| • | No transmission component slipping DTC P1870 |
| • | The engine speed is greater than 450 RPM for 5 seconds |
| • | The engine is not in fuel cutoff |
| • | The vehicle speed is greater than 24 km/h (15 mph) |
| • | The TP angle is 13-50% |
| • | The engine torque is between 50-400 ft. lbs. |
| • | The engine vacuum is between 0-105 kPa. |
| • | The gear range is D4 |
| • | The shift solenoid performance counters are zero |
| • | The TFT is 20-130°C (68-266°F) |
Conditions for Setting the DTC
DTC P1875 sets if one of the following conditions occurs:
Condition 1
| • | The 4WD low switch is in 4WD low. |
| • | The transfer case is not in 4WD low. |
| • | The TCC slip speed is -7000 to -250 RPM. |
| • | The transfer case ratio is 0.08-1.9 (the transfer case ratio is the engine speed divided by the transfer case output speed). |
| • | All conditions are met twice for 3 seconds. |
Condition 2
| • | The 4WD low switch is not in 4WD low. |
| • | The transfer case is in 4WD low. |
| • | The TCC is commanded ON. |
| • | The TCC slip speed is 1000 to 3000 RPM. |
| • | The transfer case ratio is 2.5-2.9. |
| • | All conditions met for 10 seconds. |
Action Taken When the DTC Sets
| • | The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. |
| • | The PCM commands a normal shift pattern (not a 4WD low shift pattern). |
| • | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records. |
| • | The PCM stores DTC P1875 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met. |
Conditions for Clearing the MIL/DTC
| • | The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes. |
| • | A scan tool can clear the MIL/DTC. |
| • | The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring. |
| • | The PCM cancels the DTC default actions when the fault no longer exists and/or the ignition switch is OFF long enough in order to power down the PCM. |
Diagnostic Aids
| • | Inspect the connectors at the PCM, the transfer case control module (active transfer case vehicles), the transfer case switch connector (non-active transfer case vehicles) and all other circuit connecting points for an intermittent condition. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
| • | Inspect the circuit wiring for an intermittent condition. Refer to Testing for Electrical Intermittents in Wiring Systems. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for a short to ground in the 4WD low signal circuit (CKT 1694).
-
This step tests for an open in the 4WD low signal circuit (CKT 1694) or a faulty transfer case control module (active transfer case vehicles), or transfer case switch (non-active transfer case vehicles).
Step | Action | Value(s) | Yes | No | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Powertrain Diagnostic System Check? | -- | Go to Powertrain On Board Diagnostic (OBD) System Check (4.8L/5.3L) in Engine Controls | |||||||||||||
2 |
Important: Before clearing the DTC, use the Scan Tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the PCM. Important: It may be necessary to drive the vehicle slightly forward to engage 4LO on the transfer case. Does the Scan Tool 4WD Low display Disabled when you select 4HI, then Enabled when you select 4LO? | -- | Go to Diagnostic Aids | |||||||||||||
Does the Scan Tool 4WD Low indicate Enabled? | -- | |||||||||||||||
Does the Scan Tool 4WD Low indicate Enabled when the 4WD low signal circuit (1694) is grounded? | -- | |||||||||||||||
5 | Replace the transfer case control module (active transfer case vehicles), or the transfer case selector switch (non-active transfer case vehicles). Refer to Transfer Case Shift Control Module Replacement (Automatic 4WD) (active transfer case vehicles), or Transfer Case Switch Replacement (non-active transfer case vehicles). Did you complete the replacement? | -- | -- | |||||||||||||
6 | Test the 4WD low signal circuit (CKT 1694) for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||||||||||||||
7 | Test the 4WD low signal circuit (CKT 1694) for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||||||||||||||
8 | Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls. Did you complete the replacement? | -- | -- | |||||||||||||
9 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | System OK |
