GM Service Manual Online
For 1990-2009 cars only

Linear Shift Assembly - Disassemble - Off Vehicle Column Shift


    Object Number: 324874  Size: SH

    Caution: This vehicle is equipped with a Supplemental Inflatable Restraint (SIR) System. Failure to follow the correct procedure could cause the following conditions:

       • Air bag deployment
       • Personal injury
       • Unnecessary SIR system repairs
    In order to avoid the above conditions, observe the following guidelines:
       • Refer to SIR Component Views in order to determine if you are performing service on or near the SIR components or the SIR wiring.
       • If you are performing service on or near the SIR components or the SIR wiring, disable the SIR system. Refer to Disabling the SIR System.

  1. Disable the inflatable restraint steering wheel module. Refer to Disabling the SIR System in SIR.
  2. Remove the shift lever. Refer to Shift Lever Replacement - On Vehicle .
  3. Remove the upper and lower trim covers. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle .
  4. Disconnect the park lock cable assembly (1).
  5. The steering column lock cylinder set should be in the OFF-LOCK position.
  6. Insert a small screwdriver into the slot on the lock module assembly and push against the locking tab to remove.

  7. Object Number: 662195  Size: SH
  8. Disconnect the automatic transmission shift lock control connector from the park position switch assembly.
  9. Slide the park position switch assembly off of the linear shift assembly.

  10. Object Number: 324906  Size: SH

    Notice: Do not use excessive force when removing the automatic transmission shift lock control from the steering column. Using excessive force may cause damage to the automatic transmission shift lock control and/or the steering column.

  11. Remove the automatic transmission shift lock control from the steering column.
  12. Use a small screwdriver to pry the automatic transmission shift lock control from the steering column jacket assembly.

  13. Object Number: 662202  Size: SH
  14. Remove the 3 TORX® screws from the linear shift assembly.
  15. Remove the linear shift assembly from the steering column support assembly.

Linear Shift Assembly - Disassemble - Off Vehicle Export

  1. Remove the upper and lower trim covers. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle .

  2. Object Number: 324874  Size: SH
  3. Disconnect the park lock cable assembly (1).
  4. The steering column lock cylinder set should be in the OFF-LOCK position.
  5. Insert a small screwdriver into the slot on the lock module assembly and push against the locking tab to remove.

  6. Object Number: 662195  Size: SH
  7. Disconnect the automatic transmission shift lock control connector from the park position switch assembly.
  8. Slide the park position switch assembly off of the linear shift assembly.

  9. Object Number: 324906  Size: SH
  10. Remove the automatic transmission shift lock control from the steering column.
  11. Use a small screwdriver to pry the automatic transmission shift lock control from the steering column jacket assembly.

  12. Object Number: 662202  Size: SH
  13. To break the linear shift assembly down proceed to step 12.
  14. Remove the 3 TORX® screws from the linear shift assembly.
  15. Remove the linear shift assembly from the steering column support assembly.

  16. Object Number: 662173  Size: SH
  17. Remove the 2 hexagon flange head bolts (2).
  18. Remove the ball and actuator assembly (1).
  19. Remove the cable shift cam assembly (3).

  20. Object Number: 662176  Size: SH
  21. Remove the shift actuator shaft.

  22. Object Number: 662186  Size: SH
  23. Remove the 2 actuator bushings.

  24. Object Number: 662190  Size: SH
  25. Remove the 3 oval head screws (2) from the shift lever gate (3).
  26. Remove the shift lever gate (3) from the gear shift lever assembly support bracket (1).