GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 GMC_Truck 🢒 2000 🢒 Yukon - 2WD 🢒 General Information 🢒 General Information 🢒 Electronic Suspension Rear Position Sensor Replacement - Right Side

Electronic Suspension Rear Position Sensor Replacement - Right Side 25 Series

Removal Procedure
  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the wheel from the vehicle. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.

    3. Object Number: 582406 Size: SH
  3. Disconnect the sensor harness connector from the vehicle harness connector.
  4. Disconnect the sensor link from the ball stud.

    5. Object Number: 582403 Size: SH
  5. Remove the bolts.
  6. Remove the position sensor from the vehicle.

Installation Procedure

    Object Number: 582403 Size: SH
  1. Install the position sensor on the vehicle.

    2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the bolts.

    3. Tighten
    Tighten the bolts to 12 N·m (106 lb in).

  3. Connect the sensor link to the ball stud.

    4. Object Number: 582406 Size: SH
  4. Connect the sensor harness connector to the vehicle harness connector.
  5. Install the wheel onto the vehicle. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  6. Lower the vehicle.

Electronic Suspension Rear Position Sensor Replacement - Right Side 15 Series

Removal Procedure
  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the wheel and tire assembly from the vehicle. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.

    3. Object Number: 582438 Size: SH
  3. Disconnect the sensor harness connector from the vehicle harness connector.
  4. Remove the bolt from the Real Time Damping (RTD) sensor link bracket.
  5. Spread the bracket open until the bracket can be removed from the upper control arm.
  6. Remove the bolts from the frame.
  7. Remove the position sensor from the vehicle.

Installation Procedure

    Object Number: 582438 Size: SH
  1. Install the position sensor on the vehicle.

    2. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  2. Install the bolts to the frame.

    3. Tighten
    Tighten the bolts to 12 N·m (106 in lb).


    Object Number: 608824 Size: SH
  3. Close the bracket around the upper control arm making sure the bracket rests between the locating stops.
  4. Install the bolt.

    5. Tighten
    Tighten the bolt to 25 N·m (18 ft lb.)

  5. Connect the sensor harness connector to the vehicle harness connector.
  6. Install the wheel and tire assembly to the vehicle. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  7. Lower the vehicle.