The 2-3 shift solenoid (SS) valve controls the fluid flow acting on the 2-3 shift valves. The 2-3 SS valve is a normally-open exhaust valve that is used with the 1-2 SS valve in order to allow four different shifting combinations.
When the PCM detects a 1-2-2-1 shift pattern, then DTC P0757 sets. DTC P0757 is a type A DTC.
• | No TP sensor DTCs P0122 or P0123. |
• | No VSS assembly DTCs P0502 or P0503. |
• | No TCC solenoid valve DTC P0740. |
• | No TCC stuck ON DTC P0742. |
• | No 1-2 SS valve DTC P0753. |
• | No 2-3 SS valve DTC P0758. |
• | No 3-2 SS valve assembly DTC P0785. |
• | No TFP manual valve position switch DTC P1810. |
• | No TCC PWM solenoid valve DTC P1860. |
• | The engine speed is greater than 450 RPM for 5 seconds. |
• | The engine is not in fuel cutoff. |
• | The gear range is D4. |
• | The TP angle is greater than 10 percent. |
• | The transmission fluid temperature is 20-130°C (68-266°F). |
• | The system voltage is 10-18 volts. |
• | The engine torque is 0-542 N·m (0-400 lb ft). |
• | The transmission output speed is 150 RPM or greater. |
• | The transfer case ratio in 4WD low is 0.9-1.2. |
• | The transfer case ratio in 4WD high is 2.6-2.85. |
DTC P0757 sets if both of the following conditions occur:
• | The PCM commands third gear for 1 second. |
• | The estimated gear ratio is 1.6-1.8. |
• | The engine torque is 36-368 N·m (50-500 lb ft). |
• | All conditions are met for 2 seconds. |
• | The PCM commands fourth gear for 1 second. |
• | The estimated gear ratio is 1.8-3.3. |
• | The engine torque is 0-295 N·m (50-400 lb ft). |
• | All conditions are met for 2 seconds. |
• | The PCM illuminates the malfunction indicator lamp (MIL). |
• | The PCM commands third gear only. |
• | The PCM commands maximum line pressure. |
• | The PCM inhibits TCC engagement. |
• | The PCM freezes shift adapts from being updated. |
• | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records. |
• | The PCM stores DTC P0757 in PCM history. |
• | The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes. |
• | A scan tool can clear the MIL/DTC. |
• | The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring. |
• | The PCM cancels the DTC default actions when the fault no longer exists and/or the ignition switch is OFF long enough in order to power down the PCM. |
• | Verify that the transmission meets the specifications in the Shift Speed table. |
• | Other internal transmission failures may cause more than one shift to occur. |
Refer to the Shift Solenoid Valve State and Gear Ratio table. |
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Value(s) | Yes | No | ||||||
---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Powertrain Diagnostic System Check? | -- | Go to Diagnostic System Check - Engine Controls in Engine Controls - 4.3 L or Diagnostic System Check - Engine Controls in Engine Controls - 4.8 L, 5.3 L and 6.0 L | |||||||
Important: Before clearing the DTC, use the Scan Tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the PCM. Accelerate the vehicle, ensuring that the PCM commands 1st, 2nd, 3rd and 4th gears. Did you detect a 1-2-2-1 shift pattern? | -- | Go to Intermittent Conditions in Engine Controls - 4.3 L or Intermittent Conditions in Engine Controls - 4.8 L, 5.3 L and 6.0 L | ||||||||
3 | Inspect the shift solenoid/hydraulic circuit for the following conditions:
Did you find and correct the condition? | -- | -- | |||||||
4 | Perform the following procedure in order to verify the repair:
Hold the throttle at 15% and accelerate to 80 km/h (55 mph). Has the test run and passed? | -- | System OK |