As the wheel spins, the wheel speed sensor produces an AC signal. The electronic brake control module (EBCM) uses the frequency of the AC signal to calculate the wheel speed.
The ignition is ON.
The vehicle speed is greater than 32 km/h (20 mph) when the brake is applied or 19 km/h (12 mph) when the brake is released.
The EBCM detects an open or shorted wheel speed sensor or wheel speed sensor circuit for 500 milliseconds.
The corresponding wheel speed sensor signal is less than 6 km/h (4 mph) for 5 seconds, or 120 seconds in order to set both DTCs.
The EBCM detects an erratic signal from the corresponding wheel speed sensor for 105 milliseconds.
If equipped, the following actions occur:
• | The EBCM disables the ABS/traction control system (TCS). |
• | The ABS indicator turns ON. |
• | The TRACTION OFF indicator turns ON. |
If equipped, the following actions occur:
• | The EBCM disables the ABS/TCS and may disable dynamic rear proportioning (DRP). |
• | The ABS indicator turns ON. |
• | The TRACTION OFF indicator turns ON. |
• | The red Brake warning indicator may turn ON. |
• | Repair the condition responsible for setting the DTC. |
• | Use a scan tool in order to clear the DTC. |
• | After the DTC is cleared and the ignition is ON, the ABS indicator may remain ON until the EBCM completes a power-up self-test. This test concludes when the vehicle reaches a speed greater than 13 km/h (8 mph) and the wheel speeds are verified by the EBCM. |
Operating the vehicle on extremely rough terrain can set DTC C0223, C0227 or C0229 even if the system is functioning normally.
Thoroughly inspect connections or circuitry that may cause an intermittent malfunction. Refer to the following:
If the customer concern is that the ABS indicator is ON only during humid conditions such as rain, snow or vehicle wash, thoroughly inspect the wheel speed sensor circuits for signs of water intrusion. Use the following procedure in order to help isolate the problem area:
Repair or replace the suspect harness if the DTC sets.
The numbers below refer to the step numbers on the diagnostic table.
Measure the resistance of the wheel speed sensor in order to determine if the sensor has a valid resistance value.
Ensures that the wheel speed sensor is generating a valid AC voltage output.
Step | Action | Values | Yes | No | ||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Antilock Brake System Schematics Connector End View Reference: Antilock Brake System Connector End Views Important: If DTC C0229 is set, diagnose DTC C0229 before diagnosing any other wheel speed sensor DTCs. | ||||||||||||
1 | Did you perform the ABS Diagnostic System Check? | -- | Go to Step 2 | |||||||||
2 |
Does the DTC set? | 19 km/h (12 mph) | Go to Step 3 | Go to Diagnostic Aids | ||||||||
Does the resistance measure within the specified range? | 700-10,000 ohms | Go to Step 4 | Go to Step 8 | |||||||||
Does the AC voltage measure greater than the specified value? | 100 mV | Go to Step 5 | Go to Step 8 | |||||||||
5 | Inspect for poor connections at the harness connector of the wheel speed sensor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 6 | ||||||||
6 |
Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 7 | ||||||||
7 | Inspect for poor connections at the harness connector for the EBCM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 | ||||||||
8 | Replace the wheel speed sensor. Refer to Wheel Speed Sensor Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||||
9 |
Important: Use the scan tool in order to perform the Tire Size Calibration procedure. Replace the EBCM. Refer to Electronic Brake Control Module Replacement . Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||||
10 |
Does the DTC reset? | -- | Go to Step 2 | System OK |