- Apply sealant GM P/N 12346004 (Canadian P/N 10953480),
or equivalent, to the engine coolant drain hole plug threads.
Notice: Refer to Fastener Notice in the Preface section.
- Install the engine coolant drain hole plug into the block.
Tighten
Tighten the engine coolant drain hole plug to 60 N·m (40 lb ft).
- Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the engine
block coolant heater threads, if applicable.
- Install the engine block coolant heater into the block.
Tighten
Tighten the engine block coolant heater to 50 N·m (37 lb ft).
- Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the threads
of the oil gallery plugs.
- Install the engine block top oil gallery plugs.
Tighten
Tighten the top oil gallery plugs to 20 N·m (15 lb ft).
- Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the left
side oil gallery plug threads.
- Install the engine block left side oil gallery plug.
Tighten
Tighten the left side oil gallery plug to 30 N·m (22 lb ft).
- Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the front
oil gallery plug threads.
- Install the front oil gallery plugs.
Tighten
Tighten the front oil gallery plugs to 30 N·m (22 lb ft).
- Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the rear
oil gallery plug threads.
- Install the rear oil gallery plugs.
Tighten
Tighten the rear oil gallery plugs to 20 N·m (15 lb ft).
- Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the engine block oil cooler
hose fitting threads.
- Install the engine block oil cooler hose fittings.
Tighten
Tighten the engine block oil cooler hose fittings to 23 N·m (17 lb ft).
Important: Do not overtighten the knock sensor.
- Install the left knock sensor to the engine block.
Tighten
Tighten the left knock sensor to 20 N·m (15 lb ft).
- Install the left side knock sensor heat shield.
- Install the left side knock sensor heat shield bolts.
Tighten
Tighten the bolts to 12 N·m (106 lb in).
Important: Do not overtighten the knock sensor.
- Install the right knock sensor (719) to the engine block.
Tighten
Tighten the right side knock sensor to 20 N·m (15 lb ft).
- Install the right side knock sensor heat shield (720) and bolts (721).
Tighten
Tighten the bolts to 12 N·m (106 lb in).
- Apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the engine
block coolant drain hole plug threads.
- Install the engine block coolant drain hole plugs.
Tighten
Tighten the coolant drain hole plugs to 30 N·m (22 lb ft).
- Apply sealer GM P/N 12377901 (Canadian P/N 10953504) to the outside diameter (OD) of the new camshaft
rear bearing hole plug.
- Install the NEW camshaft rear bearing hole plug to the proper depth of 6.2-7.6 mm (0.244-0.299 in) (a).
- Apply sealant GM P/N 12346004 (Canadian P/N 10953480),
or equivalent, to the oil pressure sensor threads.
- Install the oil pressure sensor.
Tighten
Using the
J 41712
(1), tighten the oil pressure sensor to 30 N·m (22 lb ft).