GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Generic 🢒 2006 🢒 Unit Repair 🢒 Engine 🢒 Engine Mechanical - 6.0L 🢒 Oil Pan Installation

Oil Pan Installation VE


    Object Number: 1552564 Size: SH

    Important: 

       • The alignment of the structural oil pan is critical. The rear bolt hole locations of the oil pan provide mounting points for the transmission housing. To ensure the rigidity of the powertrain and correct transmission alignment, it is important that the rear of the block and the rear of the oil pan are flush, or even. The rear of the oil pan must NEVER protrude beyond the engine block and transmission housing plane.
       • Do not use the oil pan gasket again.
       • It is not necessary to rivet the NEW gasket to the oil pan.

  1. Install the baffle, as required. Refer to Oil Pan Cleaning and Inspection .
  2. Apply a 5 mm (0.2 in) bead of sealant GM P/N 12378521 (Canadian P/N 88901148), or equivalent, 20 mm (0.8 in) long to the engine block. Apply the sealant directly onto the tabs of the front cover gasket that protrude into the oil pan surface. Refer to Adhesives, Fluids, Lubricants, and Sealers .

    3. Object Number: 63175 Size: SH
  3. Apply a 5 mm (0.2 in) bead of sealant GM P/N 12378521 (Canadian P/N 88901148), or equivalent, 20 mm (0.8 in) long to the engine block. Apply the sealant directly onto the tabs of the rear housing gasket that protrude into the oil pan surface.

    4. Object Number: 1565286 Size: SH

    Important: Ensure the oil gallery passages in the oil pan and engine block properly align with the oil pan gasket.

  4. Pre-assemble the oil pan gasket to the pan.
    5. 4.1. Install the gasket onto the oil pan.
    4.2. Install the oil pan bolts to the pan and through the gasket.
  5. Install the oil pan (400), gasket, and bolts (439 and 453) to the engine block.
  6. Tighten the bolts finger tight. Do not overtighten.

    7. Object Number: 1681942 Size: SH
  7. Place a straight edge across the rear of the engine block and the rear of the oil pan at the transmission housing mounting surfaces.

    8. Notice: Refer to Fastener Notice in the Preface section.

  8. Align the oil pan until the rear of engine block and rear of oil pan are flush, or even.

    9. Tighten

    1. Tighten the oil pan-to-block and oil pan-to-front cover bolts to 25 N·m (18 lb ft).
    2. Tighten the oil pan-to-rear housing bolts to 12 N·m (106 lb in).
  9. Measure the oil pan-to-engine block alignment (a).
    10. 9.1. Place a straight edge across the rear of the engine block and rear of oil pan at the transmission housing mounting surfaces.

            Important: The rear of the oil pan must NEVER protrude beyond the engine block and transmission housing mounting surfaces.

    9.2. Insert a feeler gage between the straight edge and the oil pan transmission housing mounting surface, and inspect to ensure there is no greater than a 0.1 mm (0.004 in) gap (a) between the pan and straight edge.
    9.3. If the oil pan alignment is not within specifications, remove the oil pan and repeat the above procedure.

Oil Pan Installation VZ


    Object Number: 260107 Size: SH

    Important: 

       • The alignment of the structural oil pan is critical. The rear bolt hole locations of the oil pan provide mounting points for the transmission housing. To ensure the rigidity of the powertrain and correct transmission alignment, it is important that the rear of the block and the rear of the oil pan are flush, or even. The rear of the oil pan must NEVER protrude beyond the engine block and transmission housing plane.
       • Do not use the oil pan gasket again.
       • It is not necessary to rivet the NEW gasket to the oil pan.

  1. Install the oil filter tube, baffle, and bypass valve. Refer to Oil Pan Cleaning and Inspection .
  2. Apply a 5 mm (0.2 in) bead of sealant GM P/N 12378521 (Canadian P/N 88901148), or equivalent, 20 mm (0.8 in) long to the engine block. Apply the sealant directly onto the tabs of the front cover gasket that protrude into the oil pan surface. Refer to Adhesives, Fluids, Lubricants, and Sealers .

    3. Object Number: 63175 Size: SH
  3. Apply a 5 mm (0.2 in) bead of sealant GM P/N 12378521 (Canadian P/N 88901148), or equivalent, 20 mm (0.8 in) long to the engine block. Apply the sealant directly onto the tabs of the rear housing gasket that protrude into the oil pan surface.

    4. Object Number: 309730 Size: SH

    Important: Ensure the oil gallery passages in the oil pan and engine block properly align with the oil pan gasket.

  4. Pre-assemble the oil pan gasket to the pan.
    5. 4.1. Install the gasket onto the oil pan.
    4.2. Install the oil pan bolts to the pan and through the gasket.
  5. Install the oil pan, gasket, and bolts to the engine block.
  6. Tighten the bolts finger tight. Do not overtighten.

    7. Object Number: 1712846 Size: SH
  7. Place a straight edge across the rear of the engine block and the rear of the oil pan at the transmission housing mounting surfaces.

    8. Notice: Refer to Fastener Notice in the Preface section.

  8. Align the oil pan until the rear of engine block and rear of oil pan are flush or even.

    9. Tighten

    1. Tighten the oil pan-to-block and oil pan-to-front cover bolts to 25 N·m (18 lb ft).
    2. Tighten the oil pan-to-rear housing bolts to 12 N·m (106 lb in).
  9. Measure the oil pan-to-engine block alignment (a).
    10. 9.1. Place a straight edge across the rear of the engine block and rear of oil pan at the transmission housing mounting surfaces.

            Important: The rear of the oil pan must NEVER protrude beyond the engine block and transmission housing mounting surfaces.

    9.2. Insert a feeler gage between the straight edge and the oil pan transmission housing mounting surface, and inspect to ensure there is no greater than a 0.1 mm (0.004 in) gap (a) between the pan and straight edge.
    9.3. If the oil pan alignment is not within specifications, remove the oil pan and repeat the above procedure.