Information Sensors/Switches Description. Geo Metro 1997

For 1990-2009 cars only

Makes 🢒 Geo 🢒 1997 🢒 Metro 🢒 Engine 🢒 Engine Controls - 1.0L 🢒 Information Sensors/Switches Description

Table 1:	Heated Oxygen Sensor 1 (HO2S 1)
Table 2:	Engine Coolant Temperature (ECT) Sensor
Table 3:	Intake Air Temperature (IAT) Sensor

Heated Oxygen Sensor 1 (HO2S 1)


(1)	Terminal Post
(2)	Element Cover
(3)	Heater
(4)	Zirconia Element
(5)	Heater Circuit Leads

The fuel control heated oxygen sensor 1 (HO2S 1) is mounted in the exhaust pipe below the exhaust manifold. The main function of the fuel control heated oxygen sensor is to provide the powertrain control module (PCM) with exhaust stream oxygen content information. This information enables the PCM to provide the proper fueling and achieve vehicle emissions that are within the mandated levels.

Operation

The HO2S 1 has a zirconia element with a thin platinum surface coating. The zirconia element generates an electromotive force when a there is a difference in the concentration of oxygen between its faces. This electromotive force is amplified by the catalytic reaction of the platinum when the zirconia element temperature rises. The inside of the zirconia element is exposed to the atmosphere (reference air) and the outside of the zirconia element is exposed to the exhaust gases. The difference in concentration between the inside and the outside of the zirconia element varies with the concentration of oxygen in the exhaust gases. A large difference in the concentration of oxygen results in about 1 volt of electromotive force. A small difference in the concentration of oxygen results in a about 0.01 volt of electromotive force.

In order for the HO2S 1 to function properly, the sensor must have a supply of clean reference air. Clean reference air is obtained through the oxygen sensor pigtail wiring. Any attempt to repair the wires, the connectors, or the terminals of the HO2S 1 pigtail wiring could result in the obstruction of the reference air. Replace the oxygen sensor if the pigtail wiring, the connector, or the terminals are damaged.

The oxygen sensor heater greatly decreases the amount of time required for the HO2S 1 to become active and begin the closed loop fuel control.

The HO2S 1 voltage should constantly fluctuate from approximately 100 mV (high oxygen content -- lean mixture) to 900 mV (low oxygen content -- rich mixture). The PCM calculates what fuel mixture commands to send to the fuel injectors by monitoring the voltage output of the oxygen sensor. The oxygen sensor voltage can be monitored with a scan tool.

Heated Oxygen Sensor 1 (HO2S 1)

Air Fuel Mixture	Exhaust O2 Content	HO2S1 Output	Fuel System Response
Lean Mixture	High Oxygen	Low Voltage	Rich Command
Rich Mixture	Low Oxygen	High Voltage	Lean Command

The oxygen sensor's ability to provide accurate and useful voltage signals can be affected by the presence of certain contaminants. The contaminants can be introduced through the fuel system or the contaminants can be airborne. Some of the contaminants that may be encountered are phosphorus, lead, silica, and sulfur. One of the more common contaminants is silica in the form of silicone. Silicone contamination may be indicated by a white powdery deposit on the portion of the HO2S that is exposed to the exhaust stream. Silicone contamination can be caused by the use of gasoline with silicone in it or by the use of RTV sealants which emit silicone into the crankcase or induction system. Oxygen sensors exposed to high concentrations of engine coolant or engine oil in the exhaust stream can also be adversely affected.

The fuel control heated oxygen sensor 1 (HO2S 1) is diagnosed for the following conditions:

•	A slow response

•	An inactive signal (output steady)

•	A signal fixed high

•	A signal fixed low

•	The heater performance

Heated Oxygen Sensor 2 (HO2S 2)


(1)	HO2S 2
(2)	Exhaust Pipe

The heated oxygen sensor 2 (HO2S 2) is located in the exhaust pipe after the catalytic converter. The powertrain control module (PCM) uses the HO2S 2 in order to monitor the oxygen storage capability of the catalytic converter.

Operation

A three-way catalytic converter (TWC) is used in order to control the emissions of hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen (NOx). The catalyst within the converter promotes a chemical reaction which oxidizes the HC and CO present in the exhaust gas. The catalyst converts the HC and CO into harmless water vapor and carbon dioxide. The catalyst also reduces NOx by converting the NOx to nitrogen. The HO2S 2 reacts to the oxygen content in the exhaust stream after it passes through the catalytic converter. The voltage signal created by the HO2S 2 sensor ranges from approximately 0.1 volt (high oxygen -- lean mixture) to 0.9 volt (low oxygen -- rich mixture). The oxygen sensor heater is required for the catalyst monitor HO2S 2 in order to become active and begin accurate catalyst monitoring. An HO2S 2 signal that appears lazy or inactive is normal. The PCM compares readings from both the HO2S 1 and the HO2S 2 in order to determine the efficiency of the catalyst in the TWC converter.

In order for the HO2S 2 to function properly, the sensor must have a supply of clean reference air. Clean reference air is obtained through the oxygen sensor pigtail wiring. Any attempt to repair the wires, the connectors, or the terminals of the HO2S 2 pigtail wiring could result in the obstruction of the reference air. Replace the oxygen sensor if the pigtail wiring, the connector or the terminals are damaged.

The oxygen sensor heater greatly decreases the amount of time required for the HO2S 1 to become active and begin the closed loop fuel control.

The catalyst monitor heated oxygen sensor 2 (HO2S 2) is diagnosed for the following functions:

•	A signal fixed low during steady state conditions or power enrichment (hard acceleration when a rich mixture should be indicated).

•	A signal fixed high during steady state conditions or decel fuel mode (deceleration when a lean mixture should be indicated).

•	The heater performance

Engine Coolant Temperature (ECT) Sensor


(1)	Distributor
(2)	Engine Coolant Temperature (ECT) Sensor

The engine coolant temperature (ECT) sensor is located in the cylinder head near the ignition distributor. The ECT sensor is a thermistor (a variable resistor that changes value when the temperature changes). The ECT sensor is connected in series with a fixed resistor in the powertrain control module (PCM). The PCM applies 5 volts to the ECT sensor. The PCM monitors the voltage drop across the ECT sensor and converts the voltage reading into a temperature value. The ECT sensor voltage reading at the PCM will vary with the changes in the engine temperature.

Engine Coolant Temperature (ECT) Sensor

Temperature	Resistance	Voltage
Low	High	High
High	Low	Low

Intake Air Temperature (IAT) Sensor


(1)	Air Cleaner
(2)	Intake Air Temperature (IAT) Sensor

The intake air temperature (IAT) sensor is located in the air cleaner. The IAT sensor is a thermistor (a variable resistor that changes value when the temperature changes). The IAT sensor is connected in series with a fixed resistor in the powertrain control module (PCM). The PCM applies 5 volts to the IAT sensor. The PCM monitors the voltage drop across the IAT sensor and converts the voltage reading into a temperature value. The IAT sensor voltage reading at the PCM will vary with the changes in the intake air temperature.

Intake Air Temperature (IAT) Sensor

Temperature	Resistance	Voltage
Low	High	High
High	Low	Low

Throttle Position (TP) Sensor


(1)	TP Sensor Electrical Connector
(2)	TP Sensor
(3)	TP Sensor Attaching Screws

The throttle position (TP) sensor detects the throttle valve opening. The TP sensor consists of a potentiometer that is connected to the throttle valve shaft on the throttle body.

A 5 volt reference voltage is applied to the TP sensor from the powertrain control module (PCM). The voltage reading at the PCM changes as the throttle plate opening increases. The PCM can calculate the throttle valve opening by monitoring the TP sensor output voltage.

The PCM uses the TP sensor signal for one of the inputs in order to control the fuel injector, the idle speed control motor and the exhaust gas recirculation solenoid vacuum valve. The PCM also converts the TP sensor voltage input into an ON/OFF signal for use by the automatic transmission.

Manifold Absolute Pressure (MAP) Sensor

The manifold absolute pressure (MAP) sensor measures the change in the intake manifold pressure (vacuum). The powertrain control module (PCM) applies 5 volts to the MAP sensor. The MAP sensor consists of a semi-conductor type pressure sensing element. The pressure sensing element converts a change in pressure into an electrical signal. The MAP sensor also contains electronic circuitry that amplifies and corrects the electrical signal. The PCM monitors the change in manifold pressure that results from the changes in RPM and engine load. A low MAP sensor voltage reading at the PCM indicates low manifold pressure. A high MAP sensor voltage reading at the PCM indicates high manifold pressure.

Vehicle Speed Sensor (VSS) (M/T Only)


(1)	Magnet
(2)	Speedometer Assembly
(3)	Reed Switch

The vehicle speed sensor (VSS) is part of the speedometer and is located in the instrument panel assembly. The VSS consists of a reed switch and a magnet. The magnet turns with the speedometer cable, causing the reed switch to turn ON and OFF. The ON and OFF frequency of the reed switch increases or decreases in proportion with the vehicle speed. The powertrain control module receives a digital signal from the VSS.

Crankshaft Position (CKP) Sensor

The crankshaft position (CKP) sensor consists of a magnet and a coil. The CKP sensor is mounted on the oil pan, behind the crank pulley. The CKP sensor has a specified air gap between the sensor core end and the crankshaft signal rotor. An AC voltage (pulse) is generated in the sensor when the crankshaft turns. The powertrain control module (PCM) receives a digital signal from the CKP sensor. The PCM uses the CKP sensor signal as one of the inputs in engine misfire monitoring.

Camshaft Position (CMP) Sensor

The camshaft position (CMP) sensor is located in the distributor. The CMP sensor consists of a signal generator and a signal rotor. An AC voltage is generated in the CMP sensor when the signal rotor turns. This digital signal (4 pulses/revolution) is sent to the powertrain control module (PCM). The PCM uses the CMP sensor signal to distinguish individual cylinders, calculate engine speed, trigger the ignition system, and help determine when to energize the fuel injector.

Fuel Level Sensor

The fuel level sensor is located in the fuel tank. The fuel level sensor sends a signal to the powertrain control module (PCM) and the fuel gauge in the instrument panel. The PCM uses the signal from the fuel level sensor as one of the monitoring conditions for detecting EVAP control system DTCs. The PCM also uses the fuel level sensor input in order to control the EVAP tank pressure control solenoid vacuum valve. If the fuel level is greater than a specified value, the PCM will operate the EVAP tank pressure control solenoid vacuum valve in order to prevent liquid fuel from flowing into the EVAP canister from the fuel tank.

A/C Idle-Up Signal

The A/C compressor control module provides an A/C idle-up signal to the powertrain control module (PCM) when the A/C compressor clutch is in operation. The PCM uses the A/C idle-up signal in order to modify the engine idle speed. The PCM will signal the idle speed control motor to activate the ISC motor plunger in order to open the throttle plate. Opening the throttle plate slightly will increase the engine speed in order to prevent a rough idle or a stalling condition.

Electrical Load Idle-Up Signal

The powertrain control module (PCM) receives a signal from the diode module when any of the following electrical loads are present:

•	HVAC blower motor

•	Rear window defogger

•	Headlights

The PCM will increase the engine idle speed when receiving the diode module input. The PCM will signal the idle speed control (ISC) motor to activate the ISC motor plunger in order to open the throttle plate. Opening the throttle plate slightly will maintain an engine speed that provides a desirable idle. The PCM will return the engine to the original idle when the diode module signal is removed. The diode module is located under the glove box near the cigarette lighter.

Closed Throttle Position (CTP) Switch

The closed throttle position (CTP) switch detects whether or not the ISC motor plunger is contacting the throttle lever screw. If the plunger is contacting the throttle lever screw, the CTP switch sends an ON signal to the PCM. When the plunger is not in contact with the throttle lever screw, the CTP switch will send an OFF signal to the PCM.

The CTP switch is located inside of the idle speed control motor. In order to service the CTP switch the idle speed control motor must be replaced.

System Voltage

The fuel injector is driven by the powertrain control module (PCM). There is a delay between when the PCM signals the fuel injector ON and when the injector actually opens and provides fuel. This delay is known as Ineffective Injection Time and is part of the normal event of electrical flow through the fuel injector solenoid coil.

Because ineffective injection time varies with system voltage, the PCM takes voltage readings and computes the required offset necessary for the proper timing of the fuel injector signal.

Clutch Pedal Position Switch

The clutch pedal position switch (CPP) is closed when the clutch pedal is depressed. The powertrain control module receives a voltage signal from the CPP switch when the CPP switch is closed and the ignition switch is in the START (crank) position. The starter motor solenoid also receives an input from the CPP switch.