Circuit Description
The four wheel drive (4WD) low circuit consists of the powertrain control module (PCM), a transfer case control module and the circuit wiring. The transfer case control module controls the 4WD low signal on the low signal circuit. When the operator selects 4WD low, the transfer case control module grounds the signal circuit, and the 4WD low signal voltage on the circuit changes from ignition voltage to zero volts. The PCM then compensates for transfer case gear reduction in the transmission output shaft speed (OSS) sensor signal. The PCM uses the transmission OSS sensor signal to adjust shift points, line pressure and torque converter clutch (TCC) scheduling.
When the PCM detects a continuous open, short to ground or short to power in the 4WD low circuit, then DTC P1875 sets. DTC P1875 is a type B DTC.
Conditions for Running the DTC
| • | No TP sensor DTCs P0122, or P0123. |
| • | No VSS assembly DTCs P0502 or P0503. |
| • | No TCC solenoid valve DTC P0740. |
| • | No TCC stuck ON DTC P0742. |
| • | No 1-2 SS valve DTCs P0751 or P0753. |
| • | No 2-3 SS valve DTCs P0756 or P0758. |
| • | No TFP manual valve position switch DTC P1810. |
| • | No TCC PWM solenoid valve DTC P1860. |
| • | The engine speed is greater than 450 RPM for 5 seconds. |
| • | The engine is not in fuel cutoff. |
| • | The vehicle speed is greater than 11 km/h (7 mph). |
| • | The TP angle is 17-50 percent. |
| • | The engine torque is 54-542 N·m (40-400 lb ft). |
| • | The engine vacuum is 0-105 kPa (0-15 psi). |
| • | The gear range is D4. |
| • | The shift solenoid performance counters are zero. |
| • | The TFT is 20-130°C (68-266°F). |
Conditions for Setting the DTC
DTC P1875 sets if one of the following conditions occurs:
Condition 1
| • | The 4WD low switch is in 4WD low. |
| • | The transfer case is not in 4WD low. |
| • | The TCC slip speed is -3,000 to -50 RPM. |
| • | The transfer case ratio is 0.08-1.2, the transfer case ratio is the engine speed divided by the transfer case output speed. |
| • | All conditions are met for 5 seconds. |
Condition 2
| • | The 4WD low switch is not in 4WD low. |
| • | The transfer case is in 4WD low. |
| • | The TCC is commanded ON. |
| • | The TCC slip speed is 100 to 3,000 RPM. |
| • | The transfer case ratio is 2.5-2.9. |
| • | All conditions are met for 10 seconds. |
Action Taken When the DTC Sets
| • | The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. |
| • | The PCM commands a normal shift pattern, not a 4WD low shift pattern. |
| • | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame and Failure Records. |
| • | The PCM stores DTC P1875 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met. |
Conditions for Clearing the MIL/DTC
| • | The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes. |
| • | A scan tool can clear the MIL/DTC. |
| • | The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring. |
| • | The PCM cancels the DTC default actions when the fault no longer exists and/or the ignition switch is OFF long enough in order to power down the PCM. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for a short to ground in the 4WD low signal circuit (CKT 1694).
-
This step tests for an open in the 4WD low signal circuit (CKT 1694) or a faulty transfer case control module.
Step | Action | Value(s) | Yes | No | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Powertrain Diagnostic System Check? | -- | Go to Step 2 | Go to Diagnostic System Check - Engine Controls in Engine Controls - 6.0L (LQ4) | ||||||||||||
2 |
Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the PCM. Important: It may be necessary to drive the vehicle slightly forward to engage 4LO on the transfer case. Does the scan tool 4WD Low display Disabled when you select 4HI, then Enabled when you select 4LO? | -- | Go to Intermittent Conditions in Engine Controls - 6.0L (LQ4) | Go to Step 3 | ||||||||||||
Does the scan tool 4WD Low indicate Enabled? | -- | Go to Step 6 | Go to Step 4 | |||||||||||||
Does the scan tool 4WD Low indicate Enabled when the 4WD low signal circuit (1694), is grounded? | -- | Go to Step 5 | Go to Step 7 | |||||||||||||
5 | Replace the transfer case control module. Refer to Transfer Case Shift Control Module Replacement in Transfer Case - BW - 4484. Did you complete the replacement? | -- | Go to Step 9 | -- | ||||||||||||
6 | Test the 4WD low signal circuit (CKT 1694) for a short to ground. Refer to Testing for Short to Ground and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 8 | ||||||||||||
7 | Test the 4WD low signal circuit (CKT 1694) for an open. Refer to Testing for Continuity and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 9 | Go to Step 8 | ||||||||||||
8 | Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 6.0L (LQ4). Did you complete the replacement? | -- | Go to Step 9 | -- | ||||||||||||
9 | Perform the following procedure in order to verify the repair:
Has the test run and passed? | -- | Go to Step 10 | Go to Step 2 | ||||||||||||
10 | With the scan tool, observe the stored information, capture info, and DTC Info. Does the scan tool display any DTCs that you have not diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List in Engine Controls - 6.0L (LQ4) | System OK |
