Step | Action | Value(s) | Yes | No | ||
|---|---|---|---|---|---|---|
Schematic Reference: Inside Rearview Mirror Schematics Connector End View Reference: Stationary Windows Connector End Views | ||||||
1 | Did you review the operation of the automatic day-night feature of the mirrors and perform the necessary inspections? | -- | Go to Step 2 | |||
2 |
Does the driver outside rearview mirror remain in a darken state? | -- | Go to Step 20 | Go to Step 3 | ||
3 |
Does the inside rearview mirror darken? | -- | Go to Step 4 | Go to Step 5 | ||
4 | While shining a bright light into the sensor on the mirror face, facing the rear window, observe the driver outside rearview mirror. Does the driver outside rearview mirror darken? | -- | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 9 | ||
5 |
Is the resistance less than the specified value? | 3 ohms | Go to Step 6 | Go to Step 18 | ||
6 |
Is the voltage within the specified range? | B+ | Go to Step 7 | Go to Step 19 | ||
7 |
Is the voltage less than the specified value? | 0.5 V | Go to Step 8 | Go to Backup Lamps Always On in Lighting Systems | ||
8 |
Is the voltage within the specified range? | B+ | Go to Step 15 | Go to Step 12 | ||
9 |
Is the voltage within the specified range? | 0.75-1.5 V | Go to Step 11 | Go to Step 10 | ||
10 | Measure the voltage between the automatic day-night signal circuit of the driver outside mirror element and a good ground. Is the voltage within the specified range? | 0.75-1.5 V | Go to Step 14 | Go to Step 13 | ||
11 |
Does the driver outside rearview mirror darken? | -- | Go to Step 16 | Go to Step 17 | ||
12 | Test the backup lamp supply voltage circuit of the inside rearview mirror for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 24 | Go to Backup Lamps Inoperative in Lighting Systems | ||
13 | Test the automatic day-night signal circuit of the driver outside rearview mirror element for an open or short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 24 | Go to Step 15 | ||
14 | Test the low reference circuit of the driver outside rearview mirror element for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 24 | Go to Step 15 | ||
15 | Inspect for poor connections at the harness connector of the inside rearview mirror. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 24 | Go to Step 21 | ||
16 | Inspect for poor connections at the harness connector of the DDM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 24 | Go to Step 22 | ||
17 | Inspect for poor connections at the harness connector of the driver outside rearview mirror. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find or correct the condition? | -- | Go to Step 24 | Go to Step 23 | ||
18 | Repair an open or high resistance in the ground circuit of the inside rearview mirror. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 24 | -- | ||
19 | Repair an open or short to ground in the ignition voltage circuit of the inside rearview mirror. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 24 | -- | ||
20 |
Important:: A short to voltage on the automatic day-night signal circuit of the driver outside rearview mirror element will cause permanent damage to the driver outside rearview mirror and the inside rearview mirror. Both mirrors will have to replaced. The following actions will need to be performed:
Important: Perform the Compass Calibration and Magnetic Variance for the inside rearview mirror with compass.
Did you complete the repair? | -- | Go to Step 24 | -- | ||
21 |
Important: Perform the Compass Calibration and Magnetic Variance for the inside rearview mirror with compass. Replace the inside rearview mirror. Refer to Inside Rearview Mirror Replacement . Did you complete the replacement? | -- | Go to Step 24 | -- | ||
22 | Replace the DDM. Refer to Door Lock and Side Window Switch Replacement - Driver Side . Is the replacement complete? | -- | Go to Step 24 | -- | ||
23 | Replace the driver outside rearview mirror. Refer to Outside Rearview Mirror Replacement . Did you complete the replacement? | -- | Go to Step 24 | -- | ||
24 | Operate the system in order to verify the repair. Did you correct the condition? | -- | System OK | Go to Step 2 | ||
