Circuit Description
The EBCM is required to operate within a specified range of voltage to function properly. During ABS and TCS operation, there are current requirements that will cause the voltage to drop. Because of this, voltage is monitored out of ABS/TCS control to indicate a good charging system condition, and also during ABS/TCS control when voltage may drop significantly. The EBCM also monitors for high voltage conditions which could damage the EBCM.
Conditions for Running the DTC
| • | The ignition switch is ON. |
| • | The DTC can be set after system initialization. |
Conditions for Setting the DTC
| • | The EBCM operating voltage falls below 9.4 volts out of ABS/TCS control, or 8.8 volts during ABS/TCS control. |
| • | The EBCM operating voltage rises above 17.4 volts. |
| • | The low voltage or the high voltage is detected for more than 500 milliseconds with the vehicle speed above 6 km/h (3.6 mph). |
Action Taken When the DTC Sets
If equipped, the following actions occur:
| • | A malfunction DTC is stored. |
| • | The ABS and the Traction Control indicators are turned on. |
| • | The ABS/TCS is disabled. |
| • | The Brake warning indicator turns on. |
Conditions for Clearing the DTC
| • | The condition for the DTC is no longer present and the DTC is cleared with a scan tool. |
| • | The electronic brake control module (EBCM) automatically clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles. |
Diagnostic Aids
| • | It is very important that a thorough inspection of the wiring and connectors be performed. Failure to carefully and fully inspect wiring and connectors may result in misdiagnosis, causing part replacement with reappearance of the malfunction. |
| • | Thoroughly inspect any circuitry that may be causing the complaint for the following conditions: |
| - | Backed out terminals |
| - | Improper mating |
| - | Broken locks |
| - | Improperly formed or damaged terminals |
| - | Poor terminal-to-wiring connections |
| - | Physical damage to the wiring harness |
| • | The following conditions may cause an intermittent malfunction: |
| - | A poor connection |
| - | Rubbed-through wire insulation |
| - | A broken wire inside the insulation |
| • | If an intermittent malfunction exists, refer to Testing for Intermittent Conditions and Poor Connections for further diagnosis. |
Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
-
This step checks if the voltage is above the maximum of the range.
-
Step 4 checks if the voltage is below the minimum of the range.
-
This step checks for the integrity of the ground circuit.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Schematic Reference: Antilock Brake System Schematics Connector End View Reference: Antilock Brake System Connector End Views or Powertrain Control Module Connector End Views | ||||
1 | Did you perform the Diagnostic System Check? | -- | Go to Step 2 | |
Is the monitored battery voltage within the specified range? | 0-17.4 V | Go to Step 4 | Go to Step 3 | |
3 | Use a J 39200 to measure the voltage between the battery positive terminal and ground. Is the voltage within the specified range? | 0-17.4 V | Go to Step 5 | Go to Symptoms - Engine Electrical in Engine Electrical |
Continue to monitor the battery voltage with the scan tool while running the engine at approximately 2000 RPM. Is the monitored battery voltage within the specified range? | 0-9.4 V | Go to Step 6 | Go to Step 5 | |
5 |
Did DTC C0896 reset? | -- | Go to Step 10 | |
Is the resistance within the specified range? | 0-5 ohms | Go to Step 8 | Go to Step 7 | |
7 | Repair open or high resistance in the ground circuit. Refer to Circuit Testing and Wiring Repairs Wiring Repairs. Is the repair complete? | -- | Go to Step 11 | -- |
8 |
Is the voltage within the specified range? | Above 9.4 V | Go to Step 9 | Go to Symptoms - Engine Electrical in Engine Electrical |
9 |
Did DTC C0896 reset? | -- | Go to Step 10 | Go to Step 11 |
10 | Replace the EBCM. Refer to Electronic Brake Control Module Replacement . Is the repair complete? | -- | Go to Step 11 | -- |
11 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
