Circuit Description
The body control module (BCM) receives a variable voltage signal from the instrument panel (I/P) dimmer switch requesting to illuminate the illumination lamps to a desired intensity. When this occurs, the BCM directly sends a variable voltage based on the I/P dimmer switch position on the instrument panel lamps dimming supply voltage circuit, controls illumination lamps dimming control circuit, and the LED dimming signal circuit.
Voltage for the instrument panel lamps dimming supply voltage circuit, controls illumination lamps dimming control circuit, and the LED dimming signal circuits is from the TBC 2A fuse in the instrument panel fuse block directly through the BCM to these circuits.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B2610 Passenger Compartment Dimming 1 Circuit
Conditions for Running the DTC
The battery voltage must be between 9-16 volts.
Conditions for Setting the DTC
| • | The controls illumination lamps dimming control circuit is open, shorted to ground, or shorted to voltage. |
| • | The instrument panel lamps dimming supply voltage circuit is open, shorted to ground, or shorted to voltage. |
| • | There is a loss of the instrument panel fuse block TBC 2A battery supply voltage to the BCM for one second. |
Action Taken When the DTC Sets
The illumination lamps will not operate or are always ON.
Conditions for Clearing the MIL/DTC
| • | This DTC will clear on current status after the condition for setting the fault is corrected. |
| • | A history DTC will clear after 100 consecutive ignition cycles without a fault present. |
| • | History and current DTCs can be cleared using a scan tool. |
Diagnostic Aids
| • | Perform a visual inspection for loose or poor connections at all related components. Refer to Testing for Intermittent Conditions and Poor Connections . |
| • | A short to ground in the following circuits will cause the TBC 2A fuse to open. |
| - | The controls illumination lamps dimming control. |
| - | Battery positive voltage from the instrument panel fuse block TBC 2A fuse. |
| • | An open in the TBC 2A fuse will cause the BCM to set the following DTCs: |
| - | B0951 |
| - | B2610 |
| - | B2625 |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step test determines if the problem exists in the headlamp switch or the BCM.
-
After replacement of the BCM you must calibrate the new module for proper operation.
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Interior Lights Dimming Schematics Connector End View Reference: Lighting Systems Connector End Views or Data Communication Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
2 | Is the TBC 2A fuse in the instrument panel fuse block open? | Go to Step 3 | Go to Step 4 |
3 | Test the controls illumination lamps dimming control circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 11 | Go to Step 8 |
4 | Test the instrument panel lamps dimming supply voltage circuit and the controls illumination lamps dimming control circuit for an open, high resistance, short to voltage or short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 11 | Go to Step 5 |
Does the test lamp illuminate? | Go to Step 6 | Go to Step 7 | |
6 | Inspect for poor connections at the harness connector of the headlamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 11 | Go to Step 9 |
7 | Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 11 | Go to Step 10 |
8 | Repair the battery positive voltage circuit of the BCM from the TBC 2A fuse in the instrument panel fuse block. Refer to Wiring Repairs . Did you complete the repair? | Go to Step 11 | -- |
9 | Replace the headlamp and instrument panel dimmer switch. Refer to Headlamp Switch Replacement . Did you complete the replacement? | Go to Step 11 | -- |
Replace the BCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 11 | -- | |
11 |
Does the DTC reset? | Go to Step 2 | System OK |
