Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC 2575 00: Headlamp Low Beam Control CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
HDLP LO Relay B+ | 2 | 2 | 2 | -- |
HI Beam Relay B+ | 3 | 3 | 3 | -- |
Flash to Pass Switch Signal | 4 | 4 | 4 | -- |
Headlamp Switch Headlamps ON Signal | B257A 00 | 1 | 1 | -- |
Headlamp Switch Headlamps OFF Signal | B257A 00 | 1 | 1 | -- |
Headlamp Switch High Beam Signal | 4 | 4 | 4 | -- |
Headlamp High Beam Relay Control | 3 | 3 | B2580 00 | -- |
Headlamp Low Beam Relay Control | 2 | 2 | B2575 00 | -- |
Headlamp and Panel Dimmer Switch Ground | -- | 1 | -- | -- |
LF Headlamp Ground | -- | 2 | -- | -- |
RF Headlamp Ground | -- | 2 | -- | -- |
Turn Signal/Multifunction Switch Ground | -- | 1 | -- | -- |
1. Headlamp Switch Malfunction 2. Headlamps Malfunction - Low Beam 3. Headlamps Malfunction - High Beam 4. Headlamp Dimmer Switch Malfunction | ||||
Circuit/System Description
When the headlamp switch is placed in the headlamp ON position, ground is applied to the body control module (BCM) through the headlamp low beam signal circuit. The BCM then applies ground to the headlamp low beam relay control circuit which energizes the low beam relay. With the low beam relay energized, the switch contacts close allowing battery voltage to flow through the LO HDLP fuses to the low beam headlamps. Ground for the left headlamp is supplied at G100 and the right headlamp receives ground at G101.
Conditions for Running the DTC
| • | Battery voltage must be between 9-16 volts. |
| • | Headlamps ON. |
Conditions for Setting the DTC
DTC B2575 00 will set when the BCM detects a short to voltage in the headlamp low beam relay control circuit.
Actions Taken When the DTC Sets
When DTC B2575 00 is present, the low beam headlamps will not operate.
Conditions for Clearing the DTC
| • | The condition responsible for setting the DTC no longer exists. |
| • | A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred. |
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Ignition OFF, disconnect the low beam relay.
- Connect a test lamp between the control circuit terminal 85 and the B+ circuit terminal 86.
- Igntion ON, command the Low Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
- If all circuits test normal, test or replace the low beam relay.
| ⇒ | If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM. |
| ⇒ | If the test lamp is always OFF, test the control circuit for a short to voltage or open/high resistance. If the circuit tests normal, replace the BCM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for BCM replacement, setup, and programming |
