Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B3715 02: Front Wiper Relay Drive Circuit Short to GroundDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
WIPER SPEED Relay B+ | 1, 2 | 1, 2 | -- | -- |
Windshield Wiper Switch Signal | B3922 00 | 1 | 1 | -- |
Windshield Wiper Switch High Signal | 4 | 2 | 2 | -- |
Windshield Wiper Motor Park Switch Signal | 3 | 3 | -- | -- |
WIPER CONTROL Relay Control | B3715 02 | 1 | 4 | -- |
WIPER SPEED Relay Control | 4 | 2 | B3875 00 | -- |
Windshield Wiper Motor High Speed Control | 2 | 2 | 4 | -- |
Windshield Wiper Motor Low Speed Control | 1 | 1 | 4 | -- |
Windshield Wiper Switch Low Reference | -- | 1, 2 | 1, 2 | -- |
Windshield Wiper Motor Ground | -- | 1, 2, 3 | -- | -- |
WIPER CONTROL Relay Ground | -- | 1 | -- | -- |
1. Delay or Low Speed Wipers Inoperative 2. High Speed Wipers Inoperative 3. Wipers Do Not Park 4. Wipers Always ON | ||||
Circuit/System Description
The body control module (BCM) monitors the control circuit of the wiper relay. The voltage level should be low while the wiper relay is de-energized and near system voltage when the relay is energized. After the BCM receives a low, intermittent, or mist signal from the wiper/washer switch, it responds by applying battery voltage through the wiper relay control circuit to the coil side of the relay, energizing the WIPER CONTROL relay.
Conditions for Running the DTC
This DTC can set only when the output is actively being requested by the BCM.
Conditions for Setting the DTC
If the BCM detects a short to ground in the wiper relay control circuit.
Action Taken When the DTC Sets
The BCM will not activate the output.
Conditions for Clearing the DTC
| • | The current DTC will become history when the request for the output is removed or when the condition for setting the fault is corrected. |
| • | The history DTC will clear after 50 consecutive ignition cycles without a fault present. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Wiper/Washer System Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, wiper switch in LOW position. Verify the windshield wipers are cycling at the low speed.
Circuit/System Testing
- Ignition OFF, disconnect the X5 harness connector at the BCM.
- Ignition ON, verify that the low speed wipers are not on.
- Install a 10A fused jumper wire between B+ and the WIPER CONTROL relay control circuit terminal 20. Verify the low speed wipers are on.
- If all circuits test normal, replace the BCM.
| ⇒ | If the low speed wipers are on, test the WIPER CONTROL relay control circuit terminal 20 for a short to voltage. If the circuit tests normal, replace the underhood fuse block. |
| ⇒ | If the low speed wipers are not on, test the relay control circuit for an open/high resistance or short to ground. If the circuit tests normal replace the underhood fuse block. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for BCM replacement, setup, and programming |
