Rear Bumper Replacement SUT

1. Lift the vehicle. Refer to Lifting and Jacking the Vehicle.
2. Remove both lower rear bolts to the inner wheel house panels.



3. Remove the spare tire carrier. Refer to Spare Tire Carrier Replacement.
4. Remove the top rear bumper step pad. Refer to Rear Bumper Step Pad Replacement.



5. Disconnect the electrical connector for the rear trailer tow receptacle at the rear bumper (1).
6. Remove the receptacle bolts (3) and receptacle (2).



7. Remove the push-in retainers (1) securing the bumper end cap (2) to the wheelhouse extensions.
8. Disconnect the rear park lamp electrical sockets.



9. Cut the tie straps (2) securing the electrical harness loom (1) to the rear bumper brackets (3).
10. Remove the rear bumper step pad. Refer to Rear Bumper Step Pad Replacement.
11. Remove the rear bumper end cap retainers and covers.



12. Remove the nuts (1, 3) securing the reinforcement bar (2) to the bumper end cap and trailer hitch bolt (4).
13. Remove the rear bumper bolts behind the removed spare tire carrier mounting plates.
14. Remove the bumper.

1. Position the rear bumper to the chassis frame.

Caution: Refer to Fastener Caution in the Preface section.

2. Install the 2 rear bumper bolts.

Tighten
Tighten the bolts to 32 N·m (24 lb ft) at the spare tire carrier mounts.

3. Install the rear tire carrier mounts (2, 3) to the bumper.
4. Install the bolts (1).

Tighten
Tighten the bolts to 95 N·m (70 lb ft).




5. Install the reinforcement bar (2) to the chassis hitch bolt and end cap.
6. Install the nuts (1, 3) and adjust the bumper height.

Tighten
Tighten the nuts to 85 N·m (63 lb ft).




7. Install the 2 outer bumper end caps (2) and secure the push-pin retainers.
8. Connect the rear park lamp electrical sockets.



9. Secure the electrical harness loom (1) to the rear bumper bracket (3) with a new tie strap (2).
10. Install the push-in retainers in order to secure the bumper end caps.



11. Install the trailer tow receptacle (2) to the rear bumper (1).
12. Install the bolts (3).

Tighten
Tighten the bolts to 9 N·m (80 lb in).




13. Secure the rear bumper step cover (1). Refer to Rear Bumper Step Pad Replacement.
14. Secure the license plate harness grommet (2) to the bumper cover.
15. Connect the trailer tow receptacle electrical connector.
16. Install the top rear bumper step pad. Refer to Rear Bumper Step Pad Replacement.
17. Install the spare tire carrier. Refer to Spare Tire Carrier Replacement.
18. Lower the vehicle. Refer to Lifting and Jacking the Vehicle.
19. Install the 2 rear lower wheelhouse liner bolts.

Tighten
Tighten the bolts to 10 N·m (89 lb in).

Rear Bumper Replacement SUV

1. Lift the vehicle. Refer to Lifting and Jacking the Vehicle.



2. Remove the rear tow eye/D-rings. Refer to Rear Tow Eye Replacement.



3. Disconnect the electrical connector for the rear trailer tow receptacle at the rear bumper (1).
4. Remove the receptacle bolts (3) and receptacle (2).



5. Remove the push-in retainers (1) securing the bumper end cap (2) to the wheelhouse extensions.
6. Remove the rear bumper end cap retainers and covers.



7. Remove the nuts (1, 3) securing the reinforcement bar (2) to the bumper end cap and trailer hitch bolt (4).
8. Remove the rear bumper bolts behind the removed spare tire carrier mounting plates.
9. Remove the bumper.

1. Position the rear bumper to the chassis frame.

Caution: Refer to Fastener Caution in the Preface section.

2. Install the 2 rear bumper bolts.

Tighten
Tighten the bolts to 32 N·m (24 lb ft) at the spare tire carrier mounts.

3. Install the rear tow eye/D-rings. Refer to Rear Tow Eye Replacement.



4. Install the reinforcement bar (2) to the chassis hitch bolt and end cap.
5. Install the nuts (1, 3) and adjust the bumper height.

Tighten
Tighten the nuts to 32 N·m (24 lb ft).

6. Install the push-in retainers in order to secure the bumper end caps.



7. Install the trailer tow receptacle (2) to the rear bumper (1).
8. Install the bolts (3).

Tighten
Tighten the bolts to 9 N·m (80 lb in).

9. Lower the vehicle. Refer to Lifting and Jacking the Vehicle.