Circuit Description
If the vehicle is equipped with a floor mounted console gearshift, an ignition lock cylinder control actuator system is used in the steering column. The purpose of the system is to prevent the ignition lock cylinder from being turned to the lock position while the transmission is in gear, this also prevents the steering wheel from being locked. The system consists of an ignition lock cylinder actuator and a park position switch. The actuator contains a pin that is spring loaded out, to prevent the ignition lock cylinder from being turned to the lock position when the gearshift is not in Park. The park position switch is located in the floor mounted gearshift assembly, as part of the automatic transmission shift lock control switch. The switch is closed with the gearshift in PARK, and open in all other positions
System Operation
When the gearshift is in the PARK position, the park position switch is closed. This applies voltage to the ignition lock cylinder actuator and the pin retracts, allowing the ignition lock cylinder to be turned to the LOCK position. When the gearshift is not in PARK, the park position switch is open. No voltage is applied to the ignition lock cylinder actuator and the spring loaded pin remains in the out position, preventing the ignition lock cylinder from being turned to LOCK. If vehicle power is lost while the ignition lock cylinder is not in the LOCK position, the system will prevent the operator from turning the ignition key to the lock position or removing the key. If the vehicle has lost power, pushing the ignition lock cylinder release button on the underside of the ignition lock cylinder will override the system and allow the key to be removed.
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Column/Ignition Lock Schematics Connector End View Reference: Steering Wheel and Column Connector End Views | |||
1 | Verify the condition is present. Does the system operate normally? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 2 |
2 | Does the automatic transmission shift lever operate normally? | Go to Step 3 | Go to Diagnostic Starting Point - Automatic Transmission Shift Lock Control in Shift Lock Control |
3 |
Were you able to turn the key to the LOCK position and remove the key? | Go to Step 4 | |
4 |
Does the test lamp turn ON and OFF with each cycle? | Go to Step 11 | Go to Step 5 |
5 | Does the test lamp remain illuminated with each cycle? | Go to Step 8 | Go to Step 6 |
6 | Connect a test lamp between the ground circuit of the ignition lock cylinder control actuator and B+ voltage. Does the test lamp illuminate? | Go to Step 7 | Go to Step 9 |
7 | Test the control circuit of the ignition lock cylinder control actuator for an open. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 10 |
8 | Test the control circuit of the ignition lock cylinder control actuator for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 10 |
9 | Repair the open in the ground circuit of the ignition lock cylinder control actuator. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 14 | -- |
10 | Inspect for poor connections at the automatic transmission shift lock actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 12 |
11 | Inspect for poor connections at the ignition lock cylinder control actuator. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 14 | Go to Step 13 |
12 | Replace the automatic transmission shift lock actuator. Refer to Automatic Transmission Shift Lock Control Actuator Replacement in Shift Lock Control. Did you complete the replacement? | Go to Step 14 | -- |
13 | Replace the ignition lock cylinder control actuator. Refer to Ignition Lock Cylinder Solenoid Replacement. Did you complete the replacement? | Go to Step 14 | -- |
14 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 2 |
