Diagnostic Instructions
DTC Descriptor
DTC B2958: Security System Sensor Data Circuit High
Circuit/System Description
The Passlock™ System is provided in order to prevent vehicle theft if the ignition lock cylinder is forced to rotate. The Passlock™ controller reads the coded Passlock™ data signal. The data consists of a voltage generated by a voltage
divider network created between the Passlock™ assembly and the Passlock™ controller. If the data is correct, indicating rotation of the lock cylinder with the proper mechanically cut key, the Passlock™ controller sends a password to the powertrain
controller via serial data to indicate that engine starting should be allowed. The Passlock™ controller also interfaces with the driver displays subsystem to indicate, via the security indicator, the Passlock™ subsystem status and acute subsystem
failures.
Conditions for Running the DTC
The vehicle theft deterrent system is in the learn mode.
Conditions for Setting the DTC
| • | The ignition switch is ON. |
| • | The body control module (BCM) signal input is greater than 4.9 volts for 1 second after turning the ignition switch to the CRANK position. |
Action Taken When the DTC Sets
| • | The DTC will set only when the engine is running. |
| • | The security indicator will be ON. |
Conditions for Clearing the DTC
| • | The DTC will clear once the ignition cycle has occurred without the fault recurring. |
| • | The BCM history codes will clear once 100 concurrent ignition cycles occur without the fault recurring. |
Diagnostic Aids
| • | Inspect the Passlock™ sensor harness for an intermittent or a short to ground. |
| • | You may be directed to this table from the Diagnostic System Check - Vehicle without a DTC B2958 set. If you were directed to this table, follow all of the steps in this diagnostic table. |
| • | When directed to this table, DTC B2958 may have a history status. |
Reference Information
Schematic Reference
Immobilizer Schematics
Connector End View Reference
Master Electrical Component List
Description and Operation
Immobilizer Description and Operation
Electrical Information Reference
Scan Tool Reference
Circuit/System Testing
Important: Do not start the vehicle when momentarily placing the ignition and start switch into the CRANK position.
- Turn OFF the ignition. Back out the ignition key resistor signal terminal from the ignition and start switch harness connector. Reconnect the ignition and start switch harness connector. Turn ON the ignition, with the engine OFF. With a DMM, measure
for 5 volts at the ignition key resistor terminal. Perform the following if voltage is more than 5 volts:
| ⇒ | Inspect the ignition key resistor signal circuit for a short to voltage. Make the appropriate repair. |
| ⇒ | Inspect the BCM connector. Make the appropriate repair. |
| ⇒ | Replace the BCM. Refer to Repair Instructions. |
- Secure the ignition key resistor signal circuit terminal into the harness connector and reconnect the ignition and start switch. Disconnect the body control module (BCM) connector and back out the off/run/crank voltage circuit terminal from the BCM
harness connector. Connect the harness to the BCM. Connect a DMM between the off/run/crank voltage circuit terminal and a good ground.
Important: Do not start the vehicle. Observe the voltage while momentarily placing the ignition switch in the CRANK position. Perform the following if voltage is more than 5 volts:
| ⇒ | Inspect the off/run/crank voltage circuit for a short to voltage. Make the appropriate repair. |
| ⇒ | Inspect the ignition and start switch connector. Make the appropriate repair. |
| ⇒ | Replace the ignition and start switch. Refer to Repair Instructions. |
- Inspect the BCM connector. Make the appropriate repair. If a condition is not found with the connector, replace the BCM. Refer to Repair Instructions.
- Perform the
Programming Theft Deterrent System Components
procedure.
Repair Instructions
Perform the
Diagnostic Repair Verification
after completing the diagnostic procedure.
