Preliminary Procedure

1. Open either the RR or LR door in order to access the rear side door flare attachment screws and retainers.
2. Close the door prior to removing the flare assembly from the door.

1

Rear Side Door Flare Screw (Qty: 2)

Notice: Refer to Fastener Notice in the Preface section.

Tighten
2 N·m (18 lb in)

2

Push Pin Retainer (Qty: 3)

3

Wheelhouse Molding Retainer (Qty: 5)

Tip
Carefully pull straight outward on the flare to release the retainers from the door.

4

Rear Side Door Flare Assembly

Preliminary Procedure

1. Remove the rear wheelhouse panel. Refer to Wheelhouse Panel Replacement .
2. Remove the fuel filler pocket. Refer to Fuel Tank Filler Pipe Housing Replacement .

1

Rear Wheel Opening Flare Bolt (Qty: 4)

Notice: Refer to Fastener Notice in the Preface section.

Tighten
9 N·m (80 lb in)

2

Rear Wheel Opening Flare Retainer (Qty: 6)

Tip
Use side cutters to clip the ends of the retainers for removal.

3

Rear Wheel Opening Flare Assembly

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Preliminary Procedures

1. The component part and surface should be 21°C (70°F) prior to installation. The vehicle should remain at 21°C (70°F) for one hour after assembly to allow the adhesive to develop sufficient bond strength.
2. Clean the old adhesive tape from the door flare and wipe the surface with a clean, dry lint-free towel prior to installing the door flare.
3. When removing protective liners from the adhesive tape, be careful not to touch the tape with the hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.

1

Rear Door Flare Retainer (Qty: 4)

Tip

1. Disengage the inner retainers.
2. Using a plastic flat-bladed tool, release the adhesive tape from the flare.
3. Pull the flare outward in order to release the outer flare retainers.

2

Rear Door Flare (LH Similar)

3

Rear Door Flare Retainer (Qty: 4)

4

Double Sided Adhesive Tape

Tip
Remove the adhesive tape backing only after the flare assembly is secured to the vehicle. Completely wet-out the entire outer periphery of the flare.

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Preliminary Procedures

1. The component part and surface should be 21°C (70°F) prior to installation. The vehicle should remain at 21°C (70°F) for one hour after assembly to allow the adhesive to develop sufficient bond strength.
2. Clean the old adhesive tape from the body flare and wipe the surface with a clean, dry lint-free towel prior to installing the body flare.
3. When removing protective liners from the adhesive tape, be careful not to touch the tape with the hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.

1

Rear Body Flare Retainer (Qty: 3)

Tip

1. Disengage the inner retainers.
2. Using a plastic flat-bladed tool, release the adhesive tape from the flare.
3. Pull the flare outward in order to release the body flare retainers.

2

Rear Body Flare (LH Similar)

3

Rear Body Flare Retainer (Qty: 4)

4

Double Sided Adhesive Tape

Tip
Remove the adhesive tape backing only after the flare assembly is secured to the vehicle. Completely wet-out the entire outer periphery of the flare.

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Preliminary Procedures

1. The component part and surface should be 21°C (70°F) prior to installation. The vehicle should remain at 21°C (70°F) for one hour after assembly to allow the adhesive to develop sufficient bond strength.
2. Clean the old adhesive tape from the bumper flare and wipe the surface with a clean, dry lint-free towel prior to installing the bumper flare.
3. When removing protective liners from the adhesive tape, be careful not to touch the tape with the hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.

1

Rear Bumper Flare Retainer (Qty: 3)

Tip

1. Disengage the inner retainers.
2. Using a plastic flat-bladed tool, release the adhesive tape from the flare.
3. Pull the flare outward in order to release the bumper flare retainers.

2

Rear Bumper Flare (LH Similar)

3

Rear Bumper Flare Retainer (Qty: 3)

4

Double Sided Adhesive Tape

Tip
Remove the adhesive tape backing only after the flare assembly is secured to the vehicle. Completely wet-out the entire outer periphery of the flare.